Home › Vehicle Exterior › BODY WELD POINT › CENTER BODY PILLAR(for Double Cab)
BM3250E _01 Vehicle Exterior _040520 BODY WELD POINT _0187868 CENTER BODY PILLAR(for Double Cab) F

BODY WELD POINT  CENTER BODY PILLAR(for Double Cab)  CUT AND JOIN REPLACEMENT SECTIONS  


K123711

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

A is reused.

K124155C01
0.833,1.083 1,1.083 1,1.083 1.323,1.688 false 2.198,1.188 2.51,1.344 0.313,0.156 10 false *a 0.813,2.167 1.125,2.323 0.313,0.156 10 false *b 2.406,2.125 2.719,2.281 0.313,0.156 10 false *c 0.698,1 1.01,1.156 0.313,0.156 10 false A
*a 20 mm (0.79 in.) *b 175 mm (6.89 in.)
*c 205 mm (8.07 in.) - -


K123787

K123788C01
1.656,0.74 1.969,0.896 0.313,0.156 10 false *a 5.073,0.74 5.385,0.896 0.313,0.156 10 false *b
*a 60 mm (2.36 in.) *b 50 mm (1.97 in.)


K123789



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

HINT:

Carefully cut the rocker panel outer so not to damage A.


K123790C01
3.583,2.667 3.417,2.667 3.417,2.667 3.24,1.917 false 3.75,1.729 3.5,1 3.5,1 3.667,1 false 3.688,0.917 4,1.073 0.313,0.156 10 false *1 3.635,2.573 3.958,2.823 0.323,0.25 10 false A 2.771,1.281 3.083,1.438 0.313,0.156 10 false *a 4.635,1.281 4.948,1.438 0.313,0.156 10 false *b
*1 ROCKER PANEL OUTER - -
*a 60 mm (2.36 in.) *b 50 mm (1.97 in.)



d.

Before temporarily installing the new parts, weld the rocker panel outer, rocker extension outer, center body pillar reinforce sub-assembly upper and center body pillar sub-assembly with the standard number of welding points.

K123791C01
0.75,3.75 0.583,3.75 0.583,3.75 0.906,3.156 false 3.083,2.5 3.25,2.5 3.25,2.5 3.604,2.844 false 4.083,2.083 4.25,2.083 4.25,2.083 4.5,1.698 false 1.688,0.396 1.917,0.167 1.917,0.167 2.083,0.167 false 0.792,3.667 1.104,3.823 0.313,0.156 10 false *1 3.917,2 4.229,2.156 0.313,0.156 10 false *2 2.115,0.083 2.427,0.24 0.313,0.156 10 false *3 2.917,2.417 3.229,2.573 0.313,0.156 10 false *4 3.323,3.24 3.635,3.396 0.313,0.156 10 false *a 4.719,3.24 5.031,3.396 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER *2 ROCKER EXTENSION OUTER
*3 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER *4 CENTER BODY PILLAR SUB-ASSEMBLY
*a 10 mm (0.39 in.) - -



e.

Weld the rocker panel outer, rocker extension outer, center body pillar reinforce sub-assembly upper and center body pillar sub-assembly to the vehicle side.

K123792C01
5.083,2.167 5.25,2.167 5.25,2.167 5.583,2.5 false 3.208,2.167 3.5,1.75 3.5,1.75 3.667,1.75 false 2.385,3.635 2.333,2.583 2.333,2.583 2.188,2.583 false 2.5,4.5 2.333,4.5 2.333,4.5 2.083,3.833 false 2.531,4.417 2.844,4.573 0.313,0.156 10 false *1 2.01,2.5 2.323,2.656 0.313,0.156 10 false *2 3.698,1.656 4.01,1.813 0.313,0.156 10 false *3 4.938,2.083 5.25,2.24 0.313,0.156 10 false *4 5.667,4.177 5.979,4.333 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER *2 ROCKER EXTENSION OUTER
*3 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER *4 CENTER BODY PILLAR SUB-ASSEMBLY
*a 15 mm (0.59 in.) - -



f.

Weld the center body pillar outer and A to the vehicle side.

K123793C01
2.083,3 1.75,2.417 1.75,2.417 1.583,2.417 false 5.583,4.25 5.75,3.5 5.75,3.5 5.917,3.5 false 1.427,2.344 1.74,2.5 0.313,0.156 10 false *1 5.969,3.427 6.24,3.615 0.271,0.188 10 false A
*1 CENTER BODY PILLAR OUTER - -



g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.