Home › Vehicle Exterior › BODY WELD POINT › QUARTER LOCK PILLAR REINFORCEMENT(for Smart Cab)
BM3250E _01 Vehicle Exterior _040520 BODY WELD POINT _0187880 QUARTER LOCK PILLAR REINFORCEMENT(for Smart Cab) F

BODY WELD POINT  QUARTER LOCK PILLAR REINFORCEMENT(for Smart Cab)  CUT AND JOIN REPLACEMENT SECTIONS  


K123725

With the quarter panel cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

a.

Carefully cut the rocker panel outer so not to damage A.

K123845C01
3.833,5.333 3.667,5.333 3.667,5.333 3.375,4.792 false 2,5.417 2.167,5.417 2.167,5.417 2.75,4.667 false 3.865,5.25 4.177,5.406 0.313,0.156 10 false *1 1.844,5.333 2.094,5.594 0.25,0.26 10 false A
*1 ROCKER PANEL OUTER - -


K123846C01
1.844,0.469 2.156,0.625 0.313,0.156 10 false *a 1.802,1.833 2.115,1.99 0.313,0.156 10 false *b 4.625,1.313 4.938,1.469 0.313,0.156 10 false *c
*a 50 mm (1.97 in.) *b 25 mm (0.98 in.)
*c 55 mm (2.17 in.) - -


K123847



INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

HINT:

Carefully cut the rocker panel outer so not to damage A.


K123848C01
3.417,0.781 3.583,0.333 3.583,0.333 3.75,0.333 false 3.833,1.583 3.667,1.583 3.667,1.583 3.365,1.01 false 6.333,2.75 6.167,2.75 6.167,2.75 5.958,2.167 false 3.781,0.25 4.094,0.406 0.313,0.156 10 false *1 6.365,2.667 6.677,2.823 0.313,0.156 10 false *2 2.135,0.396 2.448,0.552 0.313,0.156 10 false *a 2.729,0.167 3.042,0.323 0.313,0.156 10 false *b 2.729,3.354 3.042,3.51 0.313,0.156 10 false *c 5.115,0.823 5.427,0.979 0.313,0.156 10 false *d 3.885,1.49 4.198,1.646 0.313,0.156 10 false A
*1 ROCKER PANEL OUTER *2 QUARTER LOCK PILLAR REINFORCEMENT SUB-ASSEMBLY
*a 390 mm (15.35 in.) *b 50 mm (1.97 in.)
*c 25 mm (0.98 in.) *d 55 mm (2.17 in.)



d.

Before temporarily installing the new parts, weld the rocker panel outer and quarter lock pillar reinforcement sub-assembly with the standard number of welding points.

K123849C01
2.469,1.833 2.833,1.417 2.833,1.417 3,1.417 false 1.083,2.802 0.917,2.25 0.917,2.25 0.75,2.25 false 0.604,2.167 0.917,2.323 0.313,0.156 10 false *1 3.031,1.333 3.344,1.49 0.313,0.156 10 false *2
*1 ROCKER PANEL OUTER *2 QUARTER LOCK PILLAR REINFORCEMENT SUB-ASSEMBLY


K123850

K123851


e.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.