Home › Vehicle Exterior › BODY WELD POINT › CAB MOUNTING NO.3 BRACKET(for Smart Cab)
BM3250E _01 Vehicle Exterior _040520 BODY WELD POINT _0187892 CAB MOUNTING NO.3 BRACKET(for Smart Cab) F

BODY WELD POINT  CAB MOUNTING NO.3 BRACKET(for Smart Cab)  ASSEMBLY REPLACEMENT  


K123739

K123956

HINT:
·

Use the same procedure for the RH and LH.

·

The procedure listed below is for the RH.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K123957C01
2.5,0.521 2.813,0.677 0.313,0.156 10 false *A 2.49,2.917 2.802,3.073 0.313,0.156 10 false *A 2.115,2.542 2.427,2.698 0.313,0.156 10 false *B 2.104,0.135 2.417,0.292 0.313,0.156 10 false *C
*A FRONT *B UPPER
*C RH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


c.

Before installing the upper body, confirm the alignment of the upper body and frame.


d.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.

K123958C01
4.667,2.583 4.417,2.583 4.417,2.583 4.208,2.135 false 2.5,0.521 2.813,0.677 0.313,0.156 10 false *A 2.115,2.542 2.427,2.698 0.313,0.156 10 false *B 2.104,0.135 2.417,0.292 0.313,0.156 10 false *C 4.708,2.5 5.021,2.656 0.313,0.156 10 false *1 3.51,0.531 3.823,0.688 0.313,0.156 10 false *a 1.938,3.885 2.25,4.042 0.313,0.156 10 false *b 5.156,4.198 5.469,4.354 0.313,0.156 10 false *c 3.51,5.469 3.823,5.625 0.313,0.156 10 false *d 4.656,0.781 4.969,0.938 0.313,0.156 10 false *e 2.5,2.917 2.813,3.073 0.313,0.156 10 false *A 2.281,0.719 2.594,0.875 0.313,0.156 10 false *e 4.885,4.542 5.198,4.698 0.313,0.156 10 false *e 4.906,3.469 5.219,3.625 0.313,0.156 10 false *e 2.135,3.354 2.448,3.51 0.313,0.156 10 false *e 2.365,3.813 2.677,3.969 0.313,0.156 10 false *e 2.833,4.854 3.146,5.01 0.313,0.156 10 false *e 3.896,5.135 4.208,5.292 0.313,0.156 10 false *e
*A FRONT *B UPPER
*C RH - -
*1 CAB MOUNTING BRACKET SUB-ASSEMBLY NO.3 - -
*a 161 mm (6.34 in.) *b 100 mm (3.94 in.)
*c 119 mm (4.69 in.) *d 118 mm (4.65 in.)
*e 5 +/- 5 mm (0.20 +/- 0.20 in.) - -



e.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.