Home › Vehicle Exterior › BODY WELD POINT › FRAME REAR CROSSMEMBER
BM3250E _01 Vehicle Exterior _040520 BODY WELD POINT _0187901 FRAME REAR CROSSMEMBER F

BODY WELD POINT  FRAME REAR CROSSMEMBER  ASSEMBLY REPLACEMENT  


K123746

With the spring bracket assembly and exhaust pipe support assembly removed.


K123977

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the RH side.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K123978C01
1.531,4.073 1.844,4.229 0.313,0.156 10 false *A 1.51,2.427 1.823,2.583 0.313,0.156 10 false *A 1.885,3.708 2.198,3.865 0.313,0.156 10 false *C 1.51,0.375 1.823,0.531 0.313,0.156 10 false *A 1.885,2.063 2.198,2.219 0.313,0.156 10 false *B 1.885,0.76 2.198,0.917 0.313,0.156 10 false *C
*A FRONT *B UPPER
*C LH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


b.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.


c.

Make sure that the welding bead at A is overlapped.

K123979C01
4.833,1.333 4.583,1.333 4.583,1.333 4.354,1 false 5.083,1.75 4.833,1.75 4.833,1.75 4.531,2.354 false 2.573,2.344 2.344,1.76 2.344,1.76 2.094,1.76 false 1.521,4.063 1.833,4.219 0.313,0.156 10 false *A 1.51,2.427 1.823,2.583 0.313,0.156 10 false *A 1.896,3.698 2.208,3.854 0.313,0.156 10 false *C 3.583,4.563 3.896,4.719 0.313,0.156 10 false *b 1.521,0.385 1.833,0.542 0.313,0.156 10 false *A 1.896,2.063 2.208,2.219 0.313,0.156 10 false *B 1.896,0.75 2.208,0.906 0.313,0.156 10 false *C 4.885,1.25 5.198,1.406 0.313,0.156 10 false *1 1.927,3.177 2.24,3.333 0.313,0.156 10 false *a 3.229,4.563 3.542,4.719 0.313,0.156 10 false *b 1.938,1.677 2.188,1.917 0.25,0.24 10 false A 5.135,1.677 5.333,1.927 0.198,0.25 10 false A
*A FRONT *B UPPER
*C LH - -
*1 FRAME CROSSMEMBER SUB-ASSEMBLY REAR - -
*a 589 mm (23.19 in.) *b 5 +/- 5 mm (0.20 +/- 0.20 in.)



d.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.