Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT
NM3250E _51 Engine / Hybrid System _038575 2KD-FTV ENGINE MECHANICAL _0178464 ENGINE UNIT GE GENERAL F

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2KD-FTV TOYOTA Direct injection 4 stroke common-rail Diesel engine (D-4D) is an in-line 4-cylinder, 2.5-liter, 16-valve DOHC, turbocharged diesel engine. This engine uses the direct injection system and common-rail system to achieve high performance, clean emissions, low noise and low vibrations.


b.

A 2KD-FTV High Version engine, which has a higher power output than the normal 2KD-FTV engine, is also available. The 2KD-FTV and 2KD-FTV High Version engines are equipped with ECMs containing engine control programs that differ from each other. However, both engines share the same mechanical components.



SPECIFICATION


Engine Type 2KD-FTV 2KD-FTV High Version
Turbocharger Type Wastegate Valve Type Turbocharger ←
Intercooler without ←
No. of Cyls. and Arrangement 4-cylinder, In-line ←
Valve Mechanism 16-valve DOHC, Belt and Gear Drive ←
Combustion Chamber Direct Injection Type ←
Manifolds Cross-flow ←
Fuel System Common-rail Type ←
Displacement 2494 cm3 (152.2 cu. in.) ←
Bore x Stroke 92.0 mm x 93.8 mm
(3.62 in. x 3.69 in.)
←
Compression Ratio 18.5 : 1 ←
Max. Output (EEC) 75 kW @ 3600 rpm ←
Max. Torque (EEC) 200 N*m @ 1200 to 3400 rpm 260 N*m @ 1600 to 2400 rpm
Valve Timing Intake Open 2° BTDC ←
Closed 31° ABDC ←
Exhaust Open 30° BBDC ←
Closed 0° ATDC ←
Firing Order 1 - 3 - 4 - 2 ←
Fuel Cetane Number 48 or higher ←
Emission Regulation - ←
Engine Service Mass (Reference)* 235 kg (518 lb) ←

*: Weight shows the figure with oil and coolant fully filled.



MAIN FEATURES


a.

This engine has been able to achieve the following performance through the use of the items listed below:

A: High performance and fuel economy

B: Low noise and vibration

C: Lightweight and compact design

D: Good serviceability

E: Clean emissions

Item A B C D E
Engine Proper A cylinder head cover sub-assembly made of plastic is used. - - ○ - -
A cylinder head sub-assembly made of aluminum alloy is used. - - ○ - -
A piston provided with combustion chamber is used. ○ ○ - - ○
Valve Mechanism An intake camshaft is driven by a timing belt, and an exhaust camshaft is driven by a gear. - ○ ○ - -
An automatic tensioner (No. 1 chain tensioner assembly) is provided for the timing belt. - - - ○ -
Cooling System Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust System A diesel throttle valve is used. ○ ○ - - ○
Fuel System An HP3 type supply pump assembly is used. ○ ○ ○ - -
A common-rail type fuel injection system is used. ○ ○ - - ○
An injector assembly is provided in the bore center. ○ ○ - - ○
Compensation values and Quick Response (QR) codes are used. ○ ○ - - ○
Serpentine Belt Drive System A serpentine belt drive system is used. - - - ○ -
Engine Control System Non-contact sensors are used as the accelerator pedal sensor assembly and diesel throttle valve position sensor. ○ - - - ○
A pilot injection control system is used. - ○ - - ○