Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037981 1GR-FE ENGINE CONTROL _0176666 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A225776E20
0.625,0.427 0.979,0.646 0.354,0.219 1.677,0.427 2.031,0.646 0.354,0.219 3.135,0.427 3.49,0.646 0.354,0.219 4.198,0.427 4.552,0.646 0.354,0.219 5.25,0.427 5.604,0.646 0.354,0.219 6.313,0.427 6.667,0.646 0.354,0.219 0.688,0.458 1.063,0.688 0.375,0.229 10 false G87 1.729,0.458 2.104,0.688 0.375,0.229 10 false G88 3.188,0.458 3.563,0.688 0.375,0.229 10 false C15 4.25,0.458 4.625,0.688 0.375,0.229 10 false C14 5.302,0.458 5.677,0.688 0.375,0.229 10 false C13 6.365,0.458 6.74,0.688 0.375,0.229 10 false C12

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G87-24 (BATT) - C13-12 (E1) Y - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G87-23 (+B) - C13-12 (E1) L - BR Power source of ECM Ignition switch ON 11 to 14 V
G87-22 (+B2) - C13-12 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
G88-28 (STA) - C13-12 (E1) GR - BR ST NO. 1 relay operation signal Cranking 5.5 V or higher
G88-12 (SPD) - C13-12 (E1) V - BR Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(see waveform 1)
G88-31 (CANH) - C13-12 (E1) B - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 2)
G87-3 (EC) - Body ground BR - - Ground circuit of ECM Always Below 1 Ω
G87-5 (FC) - C13-12 (E1) B - BR Fuel pump control Ignition switch ON 9 to 14 V
G87-4 (FPR) - C13-12 (E1) L - BR Fuel pump control Ignition switch ON, STA signal OFF 0 to 3.0 V
G87-4 (FPR) - C13-12 (E1) L - BR Fuel pump control Ignition switch ON, STA signal ON 9 to 14 V
G88-13 (NEO) - C13-12 (E1) G - BR Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation
(see waveform 3)
G88-17 (TACH) - C13-12 (E1) V - BR Engine speed signal (for DLC3) Idling with warm engine Pulse generation
(see waveform 4)
G88-25 (CANL) - C13-12 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 5)
G87-21 (IGSW) - C13-12 (E1) GR - BR Ignition switch signal Ignition switch ON 11 to 14 V
G88-34 (ST1-) - C13-12 (E1) GR - BR Stop light switch assembly signal (opposite of voltage at STP terminal) Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
G87-6 (TC) - C13-12 (E1) R - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
G88-36 (MREL) - C13-12 (E1) G - BR EFI-MAIN NO.1 relay operation signal Ignition switch ON 11 to 14 V
G88-35 (STP) - C13-12 (E1) L - BR Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
G87-2 (VPA) - G87-1 (EPA) W - G Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
G88-6 (VCPA) - G87-1 (EPA) LG - G Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
G88-5 (VPA2) - G88-4 (EPA2) GR - Y Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
G88-3 (VCP2) - G88-4 (EPA2) R - Y Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C15-34 (OC2-) - C15-33 (OC2+) R - L Camshaft timing oil control valve assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(see waveform 6)
C15-32 (OC1-) - C15-31 (OC1+) R - L Camshaft timing oil control valve assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(see waveform 6)
C12-12 (HA2A) - C12-11 (E05) L - W-B Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling with cold engine Pulse generation
(see waveform 7)
Ignition switch ON 11 to 14 V
C12-11 (E05) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C12-13 (HT2B) - C12-11 (E05) L - W-B Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C12-14 (E02) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C13-23 (E01) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C12-17 (HA1A) - C12-16 (E04) Y - W-B Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling with cold engine Pulse generation
(see waveform 7)
Ignition switch ON 11 to 14 V
C12-16 (E04) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C12-18 (HT1B) - C12-16 (E04) G - W-B Heated oxygen sensor (bank 1 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C12-20 (M-) - C13-29 (ME01) W - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(see waveform 8)
C12-19 (M+) - C13-29 (ME01) B - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(see waveform 9)
C12-5 (ACIS) - C13-12 (E1) G - BR Intake air control valve assembly (for acoustic control induction system) operation signal Ignition switch ON 11 to 14 V
C12-10 (PRG) - C13-12 (E1) L - BR Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(see waveform 10)
C13-12 (E1) - Body ground BR - - Ground circuit of ECM Always Below 1 Ω
C12-2 (#40) - C13-23 (E01) W - W-B No. 4 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C12-1 (#20) - C13-23 (E01) G - W-B No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C12-3 (#60) - C13-23 (E01) Y - W-B No. 6 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C12-8 (#50) - C13-23 (E01) L - W-B No. 5 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C12-7 (#30) - C13-23 (E01) V - W-B No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C12-6 (#10) - C13-23 (E01) L - W-B No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 11)
C13-29 (ME01) - Body ground W-B - - Ground circuit of ECM Always Below 1 Ω
C13-6 (+BM) - C13-12 (E1) W - BR Power source of throttle actuator Always 11 to 14 V
C15-23 (NSW) - C13-12 (E1) L - BR Park/Neutral position switch assembly signal Ignition switch ON and shift lever in P or N Below 1 V
Ignition switch ON and shift lever not in P or N 11 to 14 V
C15-16 (NE+) - C15-17 (NE-) B - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(see waveform 12)
C15-4 (VV2+) - C15-5 (VV2-) Y - L VVT sensor (for intake camshaft of bank 2) signal Idling with warm engine Pulse generation
(see waveform 12)
C15-10 (VV1+) - C15-11 (VV1-) R - G VVT sensor (for intake camshaft of bank 1) signal Idling with warm engine Pulse generation
(see waveform 12)
C14-11 (KNK1) - C14-12 (EKNK) B - W Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 13)
C14-5 (KNK2) - C14-6 (EKN2) R - G Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 13)
C14-17 (THA) - C13-4 (ETHW) B - BR Intake air temperature sensor signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C15-14 (VG) - C14-18 (E2G) W - R Mass air flow meter sub-assembly signal Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C14-1 (A2A+) - C13-12 (E1) G - BR Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 3.3 V*
C14-7 (A1A+) - C13-12 (E1) B - BR Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 3.3 V*
C14-9 (OX1B) - C14-10 (EX1B) W - B Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 14)
C14-23 (IGF1) - C13-12 (E1) GR - BR Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling with warm engine Pulse generation
(see waveform 15)
C14-27 (IGT5) - C13-12 (E1) W - BR No. 5 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C14-25 (IGT3) - C13-12 (E1) G - BR No. 3 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C13-27 (IGT1) - C13-12 (E1) R - BR No. 1 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C12-15 (GE01) - C13-12 (E1) - - BR Shielded ground circuit of throttle actuator Always Below 1 Ω
C15-12 (VCV1) - C13-12 (E1) W - BR Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
C13-5 (THW) - C13-4 (ETHW) R - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 60 to 120°C (140 to 248°F) 0.2 to 1.0 V
C13-2 (VCTA) - C13-3 (ETA) Y - L Power source for throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C13-9 (VTA2) - C13-3 (ETA) LG - L Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
C13-1 (VTA1) - C13-3 (ETA) B - L Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V
C14-2 (A2A-) - C13-12 (E1) R - BR Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 2.9 V*
C14-8 (A1A-) - C13-12 (E1) W - BR Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 2.9 V*
C14-3 (OX2B) - C14-4 (EX2B) L - Y Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 14)
C14-28 (IGT6) - C13-12 (E1) Y - BR No. 6 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C14-26 (IGT4) - C13-12 (E1) B - BR No. 4 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C13-28 (IGT2) - C13-12 (E1) L - BR No. 2 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 15)
C15-29 (LIN) - C13-12 (E1) P - BR LIN communication signal Ignition switch ON Pulse generation
C15-6 (VCV2) - C13-12 (E1) B - BR Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
G87-9 (PSW) - C13-12 (E1) G - BR Power steering oil pressure switch While turning steering wheel Below 1.5 V
G87-11 (ELS2) - C13-12 (E1) B - BR Electric load Defogger ON 7.5 to 14 V
Defogger OFF Below 1.5 V
G88-11 (ADJ1) - Body ground W-B - - Vehicle type designation wire harness Always Below 1 Ω

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1


A292384E01
2.813,1.25 3.271,1.448 0.458,0.198 10 GND 1.146,2.01 1.917,2.167 0.771,0.156 10 20 ms./DIV. 2.708,0.135 3.313,0.313 0.604,0.177 10 5 V/DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 2


A292386E01
1.365,1.917 2.104,2.094 0.74,0.177 10 10 μs./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A210050E08
2.833,2.385 3.167,2.542 0.333,0.156 10 GND 1.125,2.75 1.792,3.021 0.667,0.271 10 2 ms./DIV. 2.229,0.563 2.771,0.854 0.542,0.292 10 5 V/DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A292385E01
0.542,1.167 1,1.365 0.458,0.198 10 GND 0.125,0.125 0.948,0.354 0.823,0.229 10 5 V/DIV. 1.75,1.917 2.563,2.104 0.813,0.188 10 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A292387E06
3,1.375 3.344,1.573 0.344,0.198 10 false GND 2.781,0.26 3.365,0.458 0.583,0.198 10 false 1 V/DIV. 1.385,1.885 2.156,2.052 0.771,0.167 10 false 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 6


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Operation Signal
ECM Terminal Name Between OC1+ and OC1-, or OC2+ and OC2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A205412E01
2.643,0.012 3.244,0.196 0.601,0.185 10 5 V/DIV. 2.701,0.848 3.063,1.01 0.362,0.162 10 GND 1.111,1.846 1.872,2.018 0.761,0.172 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal
ECM Terminal Name Between HA1A and E04, or HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 8


A245848E01
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A208000E03
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 10


A218020E01
2.676,0.174 3.296,0.318 0.62,0.145 10 10 V/DIV. 2.806,0.925 3.143,1.065 0.337,0.14 10 GND 1.189,1.789 1.937,1.936 0.749,0.147 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A292383E01
0.667,1.583 1.125,1.781 0.458,0.198 10 GND 1.865,1.906 2.75,2.104 0.885,0.198 10 20 ms./DIV. 0.531,0.177 1.417,0.375 0.885,0.198 10 20 V/DIV.

No. 1 (to No. 6) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A207436E01
0.296,1.227 0.529,1.387 0.233,0.161 10 NE 2.994,1.227 3.331,1.387 0.337,0.161 10 GND 2.639,0.601 3.198,0.761 0.559,0.161 10 5 V/DIV. 2.994,1.779 3.331,1.940 0.337,0.161 10 GND 2.994,2.169 3.331,2.330 0.337,0.161 10 GND 1.289,2.487 2.059,2.648 0.770,0.161 10 20 ms./DIV. 0.208,1.743 0.512,1.903 0.304,0.161 10 VV1 0.208,2.029 0.512,2.189 0.304,0.161 10 VV2

Crankshaft Position Sensor Signal and VVT Sensor (for Intake Camshaft) Signal
ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 13


A283572E06
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK, or KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.




WAVEFORM 14


A292382E01
0.615,1.469 1.073,1.667 0.458,0.198 10 GND 0.479,0.177 1.469,0.365 0.99,0.188 10 0.2 V/DIV. 1.854,1.906 2.844,2.094 0.99,0.188 10 200 ms./DIV.

Heated Oxygen Sensor (Sensor 2) Signal
ECM Terminal Name Between OX1B and EX1B, or OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, item O2S B1S2 and O2S B2S2 shows the ECM values from the heated oxygen sensor.



WAVEFORM 15


A210049E13
2.875,1.667 3.208,1.813 0.333,0.146 10 false GND 2.875,2.542 3.208,2.698 0.333,0.156 10 false GND 1.177,2.646 1.927,2.833 0.75,0.188 10 false 20 ms./DIV. 2.5,0.521 3.042,0.656 0.542,0.135 10 false 2 V/DIV. 0.156,1.156 0.427,1.365 0.271,0.208 10 false IGT 0.156,2.01 0.635,2.208 0.479,0.198 10 false IGF1

Ignition Coil Assembly Signal (IGT and IGF1 Signal)
ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.