Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037981 1GR-FE ENGINE CONTROL _0176666 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN NO.1 relay, closing the contact of the EFI-MAIN NO.1 relay and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A353954E01
6.198,0.417 6.813,0.615 0.615,0.198 10 false IGSW 6.198,1.083 6.813,1.281 0.615,0.198 10 false +B 6.198,1.458 6.813,1.656 0.615,0.198 10 false +B2 6.198,2.344 6.813,2.542 0.615,0.198 10 false MREL 6.198,3.469 6.813,3.667 0.615,0.198 10 false E1 6.427,3.99 6.885,4.188 0.458,0.198 10 false ECM 5.854,0.542 6.313,0.74 0.458,0.198 10 false G87 5.906,0.354 6.219,0.552 0.313,0.198 10 false 21 5.177,0.531 5.49,0.729 0.313,0.198 10 false 2G 5.854,1.469 6.313,1.667 0.458,0.198 10 false G87 5.865,2.469 6.323,2.667 0.458,0.198 10 false G88 5.854,3.469 6.313,3.667 0.458,0.198 10 false C13 5.854,1.094 6.313,1.292 0.458,0.198 10 false G87 5.906,0.906 6.219,1.104 0.313,0.198 10 false 23 5.906,1.292 6.219,1.49 0.313,0.198 10 false 22 5.896,2.281 6.208,2.479 0.313,0.198 10 false 36 5.906,3.281 6.219,3.479 0.313,0.198 10 false 12 4.073,0.667 4.688,0.844 0.615,0.177 10 false IG2 NO.1 5.219,0.354 5.531,0.552 0.313,0.198 10 false 2 3.302,0.531 3.615,0.729 0.313,0.198 10 false 2G 3.344,0.344 3.656,0.542 0.313,0.198 10 false 1 3.25,4.5 5.188,4.865 1.938,0.365 10 false *1: w/o Entry and Start System *2: w/ Entry and Start System 1.719,1.198 2.177,1.396 0.458,0.198 10 false IG2*2 0.594,0.667 1.313,0.844 0.719,0.177 10 false AM2 NO.2 2.188,0.417 2.5,0.615 0.313,0.198 10 false 3 1.396,0.417 1.708,0.615 0.313,0.198 10 false 5 2.188,0.802 2.5,1 0.313,0.198 10 false 2 1.396,0.802 1.708,1 0.313,0.198 10 false 1 0.792,1.313 1.104,1.51 0.313,0.198 10 false 20 0.604,1.542 1.219,1.74 0.615,0.198 10 false IG1D 1.115,1.604 1.573,1.802 0.458,0.198 10 false G69 1.115,1.781 2.646,2.146 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly)*2 0.323,3.281 1.094,3.479 0.771,0.198 10 false J/B-B 0.302,3.76 1.438,4.115 1.135,0.354 10 false STRG LOCK/AM2 NO.1 1.563,3.479 1.99,3.667 0.427,0.188 10 false AM2 2.188,3.469 2.615,3.656 0.427,0.188 10 false IG2 2.531,3.5 2.958,3.688 0.427,0.188 10 false 3 1.385,3.5 1.813,3.688 0.427,0.188 10 false 4 1.521,3.906 1.833,4.104 0.313,0.198 10 false G1 1.521,4.094 2.583,4.313 1.063,0.219 10 false Ignition Switch*1 0.313,4.354 2.146,4.552 1.833,0.198 10 false FL MAIN 3.0W 0.438,5 1.51,5.198 1.073,0.198 10 false Battery 3.313,1.469 3.625,1.667 0.313,0.198 10 false 2B 3.333,1.271 3.646,1.469 0.313,0.198 10 false 1 3.594,1.625 4.24,1.979 0.646,0.354 10 false EFI-MAIN NO.1 3.979,2.25 5,2.448 1.021,0.198 10 false EFI-MAIN NO.1 5.167,2.458 5.479,2.656 0.313,0.198 10 false 2P 5.208,2.25 5.521,2.448 0.313,0.198 10 false 9 3.521,2.885 3.833,3.083 0.313,0.198 10 false 2J 3.302,2.875 3.615,3.073 0.313,0.198 10 false 5 5.167,1.469 5.479,1.667 0.313,0.198 10 false 2G 5.219,1.281 5.531,1.479 0.313,0.198 10 false 5 3.813,3.115 5.406,3.51 1.594,0.396 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)
A353955C01
0.406,1.927 0.802,2.198 0.396,0.271 1.99,2.938 1.76,2.469 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.938,2.969 2.552,3.167 0.615,0.198 10 false IGSW 0.458,1.99 0.917,2.188 0.458,0.198 10 false G87
*a Rear view of wire harness connector (to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G87-21 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Entry and Start System) B
NG (w/ Entry and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

C

8.CHECK HARNESS AND CONNECTOR (NO. 4 INSTRUMENT PANEL RELAY BLOCK - ECM)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C13-12 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
A201293C08
0.448,1.063 0.854,1.333 0.406,0.271 0.552,1.104 0.865,1.302 0.313,0.198 10 false 2B 0.323,0.271 0.635,0.469 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2B-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

4.INSPECT EFI-MAIN NO. 1 RELAY
a.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM, BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM, BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-5 - G87-23 (+B) Always Below 1 Ω
2G-5 - G87-22 (+B2) Always Below 1 Ω
2P-9 - G88-36 (MREL) Always Below 1 Ω
2J-5 - Body ground Always Below 1 Ω
2G-5 or G87-23 (+B) - Body ground and other terminals Always 10 kΩ or higher
2G-5 or G87-22 (+B2) - Body ground and other terminals Always 10 kΩ or higher
2P-9 or G88-36 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (IG2) - G87-21 (IGSW) Always Below 1 Ω
G1-3 (IG2) or G87-21 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1GR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (NO. 4 INSTRUMENT PANEL RELAY BLOCK - ECM)
a.

Disconnect the ECM connector.


b.

Remove the IG2 relay from No. 4 instrument panel relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-21 (IGSW) - IG2 Relay terminal 3 Always Below 1 Ω
G87-21 (IGSW) or IG2 Relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 INSTRUMENT PANEL RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 INSTRUMENT PANEL RELAY BLOCK)
a.

Disconnect the cable from the positive (+) battery terminal.


b.

Remove the IG2 relay from No. 4 instrument panel relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Battery cable positive (+) terminal - IG2 Relay terminal 5 Always Below 1 Ω
Battery cable positive (+) terminal or IG2 Relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR