Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT
RM3250E _51 Engine / Hybrid System _037982 1GR-FE ENGINE MECHANICAL _0177655 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16603 1.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A326689N01
2.5,1.792 3.229,1.99 0.729,0.198 10 false "DOUBLE"

Install the No. 1 idler pulley sub-assembly with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

NOTICE:
·

Do not mistakenly install the No. 2 idler pulley sub-assembly instead of the No. 1 idler pulley sub-assembly.

·

The No. 1 idler pulley sub-assembly has a "DOUBLE" mark.




Hide 16604 2.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 11452 3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A112958C01
2.948,0.979 2.833,0.979 2.833,0.979 2.802,1.188 false 3,0.865 3.188,1.052 0.188,0.188 10 false *1 3.115,1.208 3.302,1.396 0.188,0.188 10 false *a
*1 O-Ring
*a Push


Install a new O-ring to the engine oil level dipstick guide.


b.

Apply a light coat of engine oil to the O-ring.


c.

Push in the engine oil level dipstick guide end into the guide hole of the oil pan sub-assembly.


d.

Install the engine oil level dipstick guide with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 23250 6.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807 7.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 16620 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.


b.
A346194C01
2.594,0.615 2.729,0.802 0.135,0.188 10 true 1 2.667,1.417 2.823,1.615 0.156,0.198 10 false 2
V100135

Bolt A
V100136

Bolt B


Tighten bolts 1 and 2 in numerical order.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.

Tighten the other bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 70 mm (2.76 in.)
Bolt B 33 mm (1.30 in.)



Hide 12315 9.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH with the 3 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12311 10.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 11.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Install the No. 1 fuel pipe sub-assembly and No. 2 fuel pipe sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Connect the No. 2 fuel pipe sub-assembly and install the No. 2 fuel pipe clamp to the fuel pressure regulator assembly.


c.

Connect the No. 1 fuel pipe sub-assembly and install the No. 2 fuel pipe clamp to the fuel delivery pipe sub-assembly.


Hide 12262 12.INSTALL NO. 2 PCV HOSE

Hide 12261 13.INSTALL PCV HOSE

Hide 14.INSTALL WATER HOSE SUB-ASSEMBLY

a.

Install the water hose sub-assembly, and slide the 2 clamps to secure the hose.


Hide 15.INSTALL WIRE HARNESS CLAMP BRACKET

a.
A349983

for LH Side:

i.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.
A349981

for RH Side:

i.

Install the 3 wire harness clamp brackets with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



c.
A349989C01
2.26,0.469 2.417,0.667 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B


for Rear Side:

i.

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 31 N*m (316 kgf*cm, 23 ft.*lbf)



Hide 82121 16.INSTALL ENGINE WIRE

a.
A349984N01
2.917,0.698 3.135,0.885 0.219,0.188 10 true 45° 3.208,0.99 3.427,1.177 0.219,0.188 10 true 45°

Install the wire harness with the 2 bolts to the engine as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the connectors and wire harness to the engine.