Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM3250E _51 Engine / Hybrid System _037982 1GR-FE ENGINE MECHANICAL _0177656 CYLINDER HEAD A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 13711E 1.REPLACE VALVE STEM OIL SEAL

a.
A326703

Using needle-nose pliers, remove the valve stem oil seal.


b.
A326704C01
0.729,0.75 0.729,0.51 0.729,0.51 0.979,0.51 true 2.677,0.74 2.677,0.5 2.677,0.5 2.927,0.5 true 1.052,0.427 1.365,0.583 0.313,0.156 10 false *a 2.979,0.427 3.292,0.583 0.313,0.156 10 false *b 0.646,1.708 0.958,1.865 0.313,0.156 10 false *c 2.604,1.708 2.917,1.865 0.313,0.156 10 false *d
*a Gray
*b Black
*c Intake Side
*d Exhaust Side


Apply a light coat of engine oil to the valve stem oil seal.

NOTICE:

Make sure that the body identification colors of the valve stem oil seals are matching.



c.
A326705N01
2,0.135 2.177,0.135 2.177,0.135 2.49,1.021 true 1.729,0.063 2.188,0.26 0.458,0.198 10 false SST

Using SST and a hammer, push in a new valve stem oil seal.

SST
09201-41020  


Hide 2.REPLACE VALVE GUIDE BUSH

a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



b.

Place the cylinder on wooden blocks.


c.
A326706N01
0.667,0.25 0.833,0.25 0.833,0.25 1.281,0.76 true 1.135,1.313 0.833,0.25 true 0.375,0.167 0.833,0.365 0.458,0.198 10 false SST

Using SST and a hammer, tap out the intake valve guide bush from the cylinder head.

SST
09201-10000  
09201-01055  
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the valve guide bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.405 to 0.406 in.)
O/S 0.05 10.335 to 10.356 mm (0.407 to 0.408 in.)


If the valve guide bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the valve guide bush bore diameter to between 10.335 and 10.356 mm (0.407 and 0.408 in.).

If the valve guide bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Select a new valve guide bush (STD or O/S 0.05).

Valve Guide Bush:
Bush Size Specified Condition
Use STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
Use O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:
Standard Bush Length
Item Specified Condition
Intake side 34.3 to 34.7 mm (1.35 to 1.37 in.)
Exhaust side 40.3 to 40.7 mm (1.59 to 1.60 in.)



f.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



g.

Place the cylinder head on wooden blocks.


h.
A326708N01
1.667,0.167 1.833,0.167 1.833,0.167 2.083,0.75 true 1.833,0.167 1.969,1.156 true 1.385,0.083 1.844,0.281 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.

SST
09201-10000  
09201-01055  
09950-70010  (09951-07100)

Standard protrusion height:

9.3 to 9.7 mm (0.366 to 0.382 in.)



i.

Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.

Standard Oil Clearance:
Item Specified Condition
Intake side 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust side 0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE UNION

HINT:

Perform this procedure only when replacement of the union is necessary.


a.

Remove the unions from the cylinder head sub-assembly (front side) and cylinder head LH (intake port side).


b.

Apply adhesive to 2 or 3 threads of the bolt ends of new unions.

Adhesive:

Toyota Genuine Seal Adhesive 1324, Three Bond 1324 or equivalent



c.

Using a 12 mm deep socket wrench, install the 2 unions.

Torque:
14.7 N*m (150 kgf*cm, 11 ft.*lbf)

A326709C01
0.229,0.01 0.542,0.167 0.313,0.156 10 false *A 3.156,0.021 3.469,0.177 0.313,0.156 10 false *B 0.323,0.271 0.635,0.427 0.313,0.156 10 false *a 3.177,0.333 3.49,0.49 0.313,0.156 10 false *b 1.896,2.646 2.208,2.802 0.313,0.156 10 false *c 5.229,3.156 5.542,3.313 0.313,0.156 10 false *d
*A for Bank 1 *B for Bank 2
*a Front Side *b Intake Port Side
*c 67 mm (2.64 in.) *d 30 mm (1.18 in.)



Hide 11117E 4.REPLACE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

It is not necessary to remove the No. 1 straight screw plug unless it is being replaced.


a.

Using a 14 mm hexagon wrench, remove the No. 1 straight screw plug and gasket.

A328513C01
6.427,0.76 6.677,0.76 false 6.396,1.156 6.646,1.156 false 0.521,0.177 0.833,0.333 0.313,0.156 10 false *A 3.083,0.177 3.396,0.333 0.313,0.156 10 false *B 6.74,0.698 7.052,0.854 0.313,0.156 10 false *1 6.698,1.094 7.01,1.25 0.313,0.156 10 false *2
*A for Bank 1 *B for Bank 2
*1 No. 1 Straight Screw Plug *2 Gasket



b.

Using a 14 mm hexagon wrench, install a new gasket and No. 1 straight screw plug.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 11117F 5.REPLACE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

It is not necessary to remove the No. 2 straight screw plug plug unless it is being replaced.


a.

Using a 14 mm hexagon wrench, remove the No. 2 straight screw plug and gasket.

A328514C01
6.385,1.094 6.667,1.094 false 6.417,0.698 6.698,0.698 false 0.271,0.177 0.583,0.333 0.313,0.156 10 false *A 3.188,0.177 3.5,0.333 0.313,0.156 10 false *B 6.76,0.646 7.073,0.802 0.313,0.156 10 false *1 6.719,1.042 7.031,1.198 0.313,0.156 10 false *2
*A for Bank 1 *B for Bank 2
*1 No. 2 Straight Screw Plug *2 Gasket



b.

Using a 14 mm hexagon wrench, install a new gasket and No. 2 straight screw plug.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 6.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins until they reach the standard protrusion height.

Standard protrusion height:

2.7 to 3.3 mm (0.106 to 0.130 in.)


A326710C01
1.594,1.271 1.76,1.021 1.76,1.021 1.927,1.021 false 3.104,0.26 3.417,0.417 0.313,0.156 10 false *A 5.854,0.26 6.167,0.417 0.313,0.156 10 false *B 1.958,0.938 2.271,1.094 0.313,0.156 10 false *a 2.49,1.333 2.802,1.49 0.313,0.156 10 false *b 5.167,1.344 5.479,1.5 0.313,0.156 10 false *b
*A for Bank 1 *B for Bank 2
*a Protrusion Height *b Engine Front



Hide 7.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap in new straight pins until they reach the standard protrusion height.

Standard Protrusion Height:
Item Specified Condition
Straight pin A 17.5 to 19.5 mm (0.689 to 0.768 in.)
Straight pin B 7.5 to 8.5 mm (0.295 to 0.335 in.)
Straight pin C 7.0 to 9.0 mm (0.276 to 0.354 in.)


A326711C01
2.667,2.083 2.458,1.656 true 2.833,2.083 2.667,2.083 2.667,2.083 2.5,1.385 true 4.458,0.49 4.292,0.49 4.292,0.49 3.875,1.24 true 5.167,3.5 5,3.5 5,3.5 4.875,2.917 true 2.5,3.833 2.667,3.833 2.667,3.833 2.927,4.573 true 5,3.5 4.24,2.875 true 4,5.083 4.167,5.083 4.167,5.083 4.448,4.865 true 4.167,5.083 4.396,4.615 true 2.25,7 1.729,6.385 true 2.469,7 2.25,7 2.25,7 2.385,6.333 true 0.188,0.25 0.5,0.406 0.313,0.156 10 false *A 0.188,3.51 0.5,3.667 0.313,0.156 10 false *B 2.865,2.01 3.177,2.167 0.313,0.156 10 false *1 4.521,0.417 4.833,0.573 0.313,0.156 10 false *2 5.219,3.427 5.531,3.583 0.313,0.156 10 false *3 0.938,0.667 1.25,0.823 0.313,0.156 10 false *a 3.354,0.344 3.667,0.5 0.313,0.156 10 false *b 0.604,5.667 0.917,5.823 0.313,0.156 10 false *c 4.281,5.781 4.594,5.938 0.313,0.156 10 false *d 3.938,6.26 4.25,6.417 0.313,0.156 10 false *e 5.854,5.958 6.167,6.115 0.313,0.156 10 false *f 5.479,6.333 5.75,6.583 0.271,0.25 10 false *g 6.198,6.333 6.51,6.49 0.313,0.156 10 false *h 4.656,6.219 4.969,6.375 0.313,0.156 10 false *h 3.354,2.344 3.667,2.5 0.313,0.156 10 false *c 0.604,3.677 0.917,3.833 0.313,0.156 10 false *b 4,3.833 4.313,3.99 0.313,0.156 10 false *a 2.333,3.74 2.646,3.896 0.313,0.156 10 false *2 3.802,5 4.115,5.156 0.313,0.156 10 false *1 2.521,6.927 2.833,7.083 0.313,0.156 10 false *3 3.917,5.583 4.229,5.74 0.313,0.156 10 false *1 5.448,5.583 5.896,5.74 0.448,0.156 10 false *2, *3
*A for Bank 1 *B for Bank 2
*1 Straight Pin A *2 Straight Pin B
*3 Straight Pin C - -
*a Front Side *b Upper Side
*c Intake Manifold Side *d 8.0 mm (0.315 in.)
*e 34.0 mm (1.34 in.) *f 5.0 mm (0.197 in.)
*g 13.8 mm (0.543 in.) *h Protrusion Height



Hide 8.REPLACE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E6 and E7 "TORX" socket wrench, remove the stud bolts.


b.

Using an E6 and E7 "TORX" socket wrench, install new stud bolts.

Torque:
for stud bolt A : 4.0 N*m (41 kgf*cm, 35 in.*lbf)
for stud bolt B : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
for stud bolt C : 4.0 N*m (41 kgf*cm, 35 in.*lbf)

A332547C01
2,6.781 2.167,6.417 2.167,6.417 2.333,6.417 false 2.01,7.135 2.167,7.5 2.167,7.5 2.333,7.5 false 3.979,6.74 4.146,6.375 4.146,6.375 4.313,6.375 false 3.99,7.125 4.146,7.49 4.146,7.49 4.313,7.49 false 5.969,6.781 6.135,6.417 6.135,6.417 6.302,6.417 false 5.969,7.125 6.125,7.49 6.125,7.49 6.292,7.49 false 2.104,0.677 2.417,0.833 0.313,0.156 10 false *A 5.427,0.688 5.74,0.844 0.313,0.156 10 false *B 0.333,1.688 0.646,1.844 0.313,0.156 10 false *a 0.354,3.229 0.667,3.385 0.313,0.156 10 false *b 0.333,4.854 0.646,5.01 0.313,0.156 10 false *c 2.396,6.354 2.708,6.51 0.313,0.156 10 false *d 2.25,6.844 2.563,7 0.313,0.156 10 false *e 2.396,7.427 2.708,7.583 0.313,0.156 10 false *f 4.354,6.292 4.667,6.448 0.313,0.156 10 false *g 4.177,6.813 4.49,6.969 0.313,0.156 10 false *h 4.375,7.427 4.688,7.583 0.313,0.156 10 false *i 6.354,6.333 6.667,6.49 0.313,0.156 10 false *j 6.146,6.896 6.458,7.052 0.313,0.156 10 false *k 0.865,2.156 1.177,2.313 0.313,0.156 10 false A 3.26,2.25 3.563,2.427 0.302,0.177 10 false A 4.979,2.354 5.281,2.531 0.302,0.177 10 false A 6.625,2.125 6.927,2.302 0.302,0.177 10 false A 1.583,5.542 1.896,5.698 0.313,0.156 10 false B 2.271,5.552 2.583,5.708 0.313,0.156 10 false B 2.521,5.552 2.833,5.708 0.313,0.156 10 false B 4.75,5.552 5.063,5.708 0.313,0.156 10 false B 5.448,5.552 5.76,5.708 0.313,0.156 10 false B 5.708,5.552 6.021,5.708 0.313,0.156 10 false B 5.927,4.375 6.24,4.531 0.313,0.156 10 false B 5.219,4.365 5.531,4.521 0.313,0.156 10 false B 4.99,4.365 5.302,4.521 0.313,0.156 10 false B 2.75,4.365 3.063,4.521 0.313,0.156 10 false B 2.042,4.365 2.354,4.521 0.313,0.156 10 false B 1.802,4.365 2.115,4.521 0.313,0.156 10 false B 1.281,3.333 1.594,3.49 0.313,0.156 10 false C 2.208,3.906 2.51,4.063 0.302,0.156 10 false C 5.365,3.854 5.667,4.01 0.302,0.156 10 false C 6.26,3.333 6.563,3.49 0.302,0.156 10 false C 6.344,7.417 6.656,7.573 0.313,0.156 10 false *f 1.76,6.375 2.073,6.531 0.313,0.156 10 false A 3.75,6.25 4.063,6.406 0.313,0.156 10 false B 5.708,6.375 6.021,6.531 0.313,0.156 10 false C
*A for Bank 1 *B for Bank 2
*a Upper Side *b Rear Side
*c Exhaust Manifold Side *d 21 mm (0.827 in.)
*e 34 mm (1.34 in.) *f 9 mm (0.354 in.)
*g 20 mm (0.787 in.) *h 35 mm (1.38 in.)
*i 13 mm (0.512 in.) *j 16 mm (0.630 in.)
*k 27 mm (1.06 in.) - -