The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the ABS warning light remains on:
The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).
There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.
There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).
The ABS control system is defective.
w/ Rear Differential Lock:
The rear differential is locked.
In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.
When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if CAN communication system DTCs are output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1KD-FTV: Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 1GD-FTV: Click herePower Source / Network>1GD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2GD-FTV: Click herePower Source / Network>2GD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2KD-FTV: Click herePower Source / Network>2KD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 1TR-FE: Click herePower Source / Network>1TR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2TR-FE: Click herePower Source / Network>2TR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Disconnect the A3 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A3-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-1 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK (w/o Rear Differential Lock) |
| OK (w/ Rear Differential Lock) |
| NG |
OK (w/o Rear Differential Lock)
OK (w/ Rear Differential Lock)
NG
Reconnect the A3 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.
Check for DTCs.
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output |
DTCs are not output
DTCs are output
Reconnect the A3 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Warning Light | ABS warning light | OFF or ON | OFF: Warning light off
ON: Warning light on |
- |
| Tester Display |
|---|
| ABS Warning Light |
Check the GTS display condition of the ABS warning light.
| Proceed to |
|---|
| Display of the Data List remains OFF |
| Display of the Data List remains ON |
Display of the Data List remains OFF
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Display of the Data List remains ON