Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.06–2016.03
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178882 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C306841C03
0.198,0.146 0.51,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND2) Pump motor ground
2 - (Not used)
3 (EXI) 4WD detection switch (Transfer shift actuator assembly) input*1, *4
A.D.D. position switch (Differential motor actuator assembly) signal input*1, *5
4 - (Not used)
5 (EXI4)*1 L4 detection switch (Transfer shift actuator assembly) input
6 - (Not used)
7 (STP2) Stop light switch assembly input
8 - (Not used)
9 - (Not used)
10 (CANL) CAN communication line L
11 - (Not used)
12 (IG1) ECU power supply input
13 (BM) Motor relay power supply
14 (SP1) Speed signal output for speedometer
15 (RR-) Rear wheel speed RH (-) signal input
16 (RR+) Rear wheel speed RH (+) power supply output
17 (FL-) Front wheel speed LH (-) signal input
18 (FL+) Front wheel speed LH (+) power supply output
19 - (Not used)
20 (TMVC)*2, *3 Neutral position switch power supply
21 (TME2)*2, *3 Neutral position switch signal input
22 (CANH) CAN communication line H
23 - (Not used)
24 (TS) Sensor check input
25 (GND1) Skid control ECU (Brake actuator assembly) ground
26 (STPO) Stop light control relay (STOP/CDS FAN Relay) output
27 (HDCS)*2 Downhill assist control switch input
28 (RL-) Rear wheel speed LH (-) signal input
29 (RL+) Rear wheel speed LH (+) power supply output
30 (FR-) Front wheel speed RH (-) signal input
31 (FR+) Front wheel speed RH (+) power supply output
32 (TMN)*2, *3 Neutral position switch signal output
33 (CSW) VSC OFF switch input
34 - (Not used)
35 (STP) Stop light control relay (STOP/CDS FAN Relay) input
36 - (Not used)
37 - (Not used)
38 (+BS) Solenoid relay power supply

*1: for 4WD

*2: w/ Downhill Assist Control

*3: for Manual Transmission

*4: w/o A.D.D. Actuator

*5: w/ A.D.D. Actuator



TERMINAL INSPECTION


a.

Disconnect the A4 connector and measure the voltage or resistance on the wire harness side.

C306842C09
1.667,1.167 2.104,1.469 0.438,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.771,1.24 2.229,1.438 0.458,0.198 10 false A4
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A4-1 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A4-3 (EXI) - Body ground*1 W - Body ground 4WD detection switch (Transfer shift actuator assembly) input*6
·

Ignition switch ON

·

4WD control switch (Transfer position switch) set to H2


11 to 14 V
A.D.D. position switch (Differential motor actuator assembly) signal input*7
A4-5 (EXI4) - Body ground*1 G - Body ground*2 L4 detection switch (Transfer shift actuator assembly) input
·

Ignition switch ON

·

4WD control switch (Transfer position switch) not set to L4


11 to 14 V
SB - Body ground*3
A4-7 (STP2) - Body ground L - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A4-12 (IG1) - Body ground V - Body ground*3 ECU power supply input Ignition switch ON 11 to 14 V
L - Body ground*2
A4-13 (BM) - Body ground R - Body ground Motor relay power supply Always 11 to 14 V
A4-14 (SP1) - Body ground Y - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A4-20 (TMVC) - Body ground*4, *5 B - Body ground Neutral position switch power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A4-25 (GND1) - Body ground W-B - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A4-26 (STPO) - Body ground P - Body ground Stop light control relay (STOP/CDS FAN Relay) output Ignition switch ON 11 to 14 V
A4-27 (HDCS) -Body ground*5 SB - Body ground Downhill assist control switch input Downhill assist control switch on → off Below 1 Ω → 10 kΩ or higher
A4-32 (TMN) - A4-21 (TME2)*4, *5 W - R Neutral position switch signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
A4-33 (CSW) - Body ground GR - Body ground VSC OFF switch input VSC OFF switch pressed and held → released Below 1 Ω → 10 kΩ or higher
A4-35 (STP) - Body ground L - Body ground Stop light control relay (STOP/CDS FAN Relay) input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A4-38 (+BS) - Body ground B - Body ground Solenoid relay power supply Always 11 to 14 V

*1: for 4WD

*2: for 1GD-FTV RHD and 2GD-FTV RHD

*3: for all except 1GD-FTV RHD and 2GD-FTV RHD

*4: for Manual Transmission

*5: w/ Downhill Assist Control

*6: w/o A.D.D. Actuator

*7: w/ A.D.D. Actuator