Home › Engine / Hybrid System › 2TR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM3250E _51 Engine / Hybrid System _038025 2TR-FE INTAKE / EXHAUST _0181001 EXHAUST MANIFOLD A

2TR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17141 1.INSTALL EXHAUST MANIFOLD

a.
A350541C01
0.052,0.021 0.365,0.177 0.313,0.156 10 true *A 0.052,2.49 0.365,2.646 0.313,0.156 10 true *B
*A w/ Secondary Air Injection System
*B w/o Secondary Air Injection System


Install a new gasket.


b.
A346103N01
1.49,0.323 1.646,0.521 0.156,0.198 10 true 1 2.25,1.552 2.406,1.75 0.156,0.198 10 true 2 2.698,0.396 2.854,0.594 0.156,0.198 10 true 3 3.042,1.625 3.198,1.823 0.156,0.198 10 true 4 1.396,1.552 1.552,1.75 0.156,0.198 10 true 5 0.25,0.406 0.406,0.604 0.156,0.198 10 true 6

w/o Secondary Air Injection System:

Install the exhaust manifold with 6 new nuts, and tighten the nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.
A346102N01
1.448,0.021 1.604,0.219 0.156,0.198 10 true 1 2.24,1.25 2.396,1.448 0.156,0.198 10 true 2 2.885,0.375 3.042,0.573 0.156,0.198 10 true 3 1.302,1.229 1.458,1.427 0.156,0.198 10 true 5 3.083,1.323 3.24,1.521 0.156,0.198 10 true 4 0.115,0.854 0.271,1.052 0.156,0.198 10 true 6 2.906,0.073 3.063,0.271 0.156,0.198 10 true 8 0.49,0.021 0.646,0.219 0.156,0.198 10 true 7

w/ Secondary Air Injection System:

Install the exhaust manifold with 8 new nuts, and tighten the nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 17118 2.INSTALL MANIFOLD STAY

a.
A345967N01
0.698,1.708 0.854,1.906 0.156,0.198 10 true A 0.708,0.708 0.865,0.906 0.156,0.198 10 true B 2.521,1.063 2.677,1.26 0.156,0.198 10 true C

for Manual Transmission:

Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt B : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt C : 30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

for Automatic Transmission:

Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for bolt B : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt C : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 17167 3.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o Secondary Air Injection System)

a.

Install the No. 1 exhaust manifold heat insulator with the 5 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A076194C38
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




c.

Install the front exhaust pipe assembly to the No. 1 exhaust pipe support.


d.

Connect the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Install a new gasket and connect the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

for 2WD:

Connect the heated oxygen sensor connector and attach the 4 wire harness clamps.


g.

for 4WD:

Connect the heated oxygen sensor connector and attach the wire harness clamp.


h.

Connect the air fuel ratio sensor connector and attach the 3 wire harness clamps.


Hide 17701 5.INSTALL AIR CLEANER CASE SUB-ASSEMBLY (w/o Secondary Air Injection System)

Hide 17801 6.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (w/o Secondary Air Injection System)

Hide 17705 7.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE (w/o Secondary Air Injection System)

Hide 25710 8.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 53882F 10.INSTALL FRONT FENDER SEAL RH