Home › Engine / Hybrid System › 1TR-FE ENGINE CONTROL › THROTTLE BODY
RM3250E _51 Engine / Hybrid System _037997 1TR-FE ENGINE CONTROL _0181523 THROTTLE BODY A

1TR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A344401C01
1.927,1.552 2.25,1.833 2.25,1.833 2.417,1.833 true 1.927,0.729 2.25,1 2.25,1 2.417,1 true 2.417,0.917 2.667,1.083 0.25,0.167 10 true *a 2.427,1.75 2.677,1.917 0.25,0.167 10 true *b
*a Protrusion
*b Groove


Install a new gasket to the intake manifold.

HINT:

Align the protrusion of the gasket with the groove of the intake manifold.



b.

Install the throttle body with motor assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 1 water by-pass hose and No. 2 water by-pass hose to the throttle body with motor assembly, and slide the 2 hose clips to secure the hoses.


d.

Connect the throttle body with motor connector.


Hide 17861 2.INSTALL INTAKE AIR CONNECTOR

a.

Install the intake air connector with the 2 bolts, and then tighten the 2 hose clamps.

Torque:
for bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for hose clamp (throttle body with motor assembly side) : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for hose clamp (air cleaner side) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Connect the No. 1 air hose to the intake air connector, and slide the clip to secure the hose.


c.

Connect the vacuum hose.


d.

Connect the No. 2 PCV hose to the cylinder head cover sub-assembly, and slide the clip to secure the hose.


Hide 5.PERFORM INITIALIZATION

NOTICE:

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.


a.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above steps again.



b.

Connect the GTS to the DLC3 and clear the DTCs.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR


c.

Perform the "Inspection After Repairs".

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


d.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range when the A/C switched off.

Engine Idle Speed:
Condition Specified Condition
Air conditioning switched off 650 to 750 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in neutral.




e.

Enter the following menus: Powertrain / Engine / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value changes.

Powertrain > Engine > Data List
Tester Display
Throttle Sensor Position
50003 234 12

f.

Perform a road test and confirm that there are no abnormalities.