Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM3250E _56 Audio / Visual / Telematics _038053 NAVIGATION / MULTI INFO DISPLAY _0182280 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is ACC, 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E51
1.719,0.427 2.333,0.625 0.615,0.198 10 false LCL+ 1.74,1.063 2.354,1.26 0.615,0.198 10 false LCL- 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH1 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL1 2.146,0.292 2.76,0.49 0.615,0.198 10 false 38 2.135,0.938 2.75,1.135 0.615,0.198 10 false 37 4.906,0.292 5.521,0.49 0.615,0.198 10 false 3 4.906,0.927 5.521,1.125 0.615,0.198 10 false 4 0.781,1.594 1.396,1.792 0.615,0.198 10 false G9 0.781,1.75 2.75,1.979 1.969,0.229 10 false Combination Meter Assembly 4.781,1.583 5.396,1.781 0.615,0.198 10 false G114 4.781,1.74 6.75,1.969 1.969,0.229 10 false Navigation Receiver Assembly 0.906,2.219 3.271,2.448 2.365,0.229 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G114 navigation receiver assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G114-3 (CNH1) - G9-38 (LCL+) Always Below 1 Ω
G114-4 (CNL1) - G9-37 (LCL-) Always Below 1 Ω
G114-3 (CNH1) - Body ground Always 10 kΩ or higher
G114-4 (CNL1) - Body ground Always 10 kΩ or higher
G114-3 (CNH1) - G114-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G114-3 (CNH1) - Body ground Always Below 1 V
G114-4 (CNL1) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.

Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.
E317642N01
0.583,1.792 0.729,1.792 0.729,1.792 0.906,1.313 true 1.292,1.792 1.167,1.792 1.167,1.792 1.052,1.313 true 0.219,1.719 0.833,1.917 0.615,0.198 10 false LCL+ 1.344,1.698 1.958,1.896 0.615,0.198 10 false LCL-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
38 (LCL+) - 37 (LCL-) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E317643N01
1.333,1.875 1.5,1.875 1.5,1.875 2.104,1.177 true 2.354,1.875 2.146,1.875 2.146,1.875 2.25,1.177 true 2.417,1.792 3.031,1.99 0.615,0.198 10 false CNH1 0.958,1.792 1.573,1.99 0.615,0.198 10 false CNL1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK METER / GAUGE SYSTEM

NG

5.CHECK METER / GAUGE SYSTEM
a.

Turn the ignition switch to ON and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG