Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM3250E _56 Audio / Visual / Telematics _038053 NAVIGATION / MULTI INFO DISPLAY _0182280 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit.

The sound signal that has been sent is amplified by the navigation receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM

E317103E03
0.885,0.771 1.5,0.969 0.615,0.198 10 false ADPG 0.854,1.229 1.469,1.427 0.615,0.198 10 false VAR+ 0.854,1.729 1.469,1.927 0.615,0.198 10 false VAL+ 1,2.188 1.615,2.385 0.615,0.198 10 false VA- 0.865,2.667 1.479,2.865 0.615,0.198 10 false AGND 6.021,2.698 6.635,2.896 0.615,0.198 10 false AGND 6.01,2.198 6.625,2.396 0.615,0.198 10 false VA- 6,1.708 6.615,1.906 0.615,0.198 10 false VAL+ 6,1.25 6.615,1.448 0.615,0.198 10 false VAR+ 6,0.792 6.615,0.99 0.615,0.198 10 false ADPG 1.365,0.677 1.979,0.875 0.615,0.198 10 false 10 1.375,1.146 1.99,1.344 0.615,0.198 10 false 7 1.365,1.615 1.979,1.813 0.615,0.198 10 false 8 1.375,2.115 1.99,2.313 0.615,0.198 10 false 9 1.344,2.563 1.958,2.76 0.615,0.198 10 false 12 2.469,2.823 3.146,3.021 0.677,0.198 10 false * 4.833,2.844 5.51,3.042 0.677,0.198 10 false * 0.208,3.104 0.885,3.302 0.677,0.198 10 false a1 0.229,3.271 1.406,3.635 1.177,0.365 10 false No. 1 Stereo Jack Adapter Assembly 2.063,3.104 2.865,3.292 0.802,0.188 10 false Radio Wire 0.135,4.385 1.833,4.625 1.698,0.24 10 false *: Shielded 3.531,0.781 4.146,0.979 0.615,0.198 10 false aG1 3.542,1.26 4.156,1.458 0.615,0.198 10 false aG1 3.552,1.719 4.167,1.917 0.615,0.198 10 false aG1 3.563,2.208 4.177,2.406 0.615,0.198 10 false aG1 3.552,2.667 4.167,2.865 0.615,0.198 10 false aG1 3.625,0.552 4.24,0.75 0.615,0.198 10 false 5 3.625,1.042 4.24,1.24 0.615,0.198 10 false 6 3.583,1.51 4.198,1.708 0.615,0.198 10 false 13 3.646,1.99 4.26,2.188 0.615,0.198 10 false 7 3.604,2.469 4.219,2.667 0.615,0.198 10 false 14 5.698,0.646 6.313,0.844 0.615,0.198 10 false 25 5.698,1.125 6.313,1.323 0.615,0.198 10 false 26 5.719,1.604 6.333,1.802 0.615,0.198 10 false 28 5.719,2.073 6.333,2.271 0.615,0.198 10 false 27 5.729,2.573 6.344,2.771 0.615,0.198 10 false 11 5.729,3.094 6.344,3.292 0.615,0.198 10 false G113 5.75,3.271 6.99,3.646 1.24,0.375 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK RADIO WIRE
a.

Disconnect the a1 No. 1 stereo jack adapter assembly connector.


b.
E317104C01
1.479,0.146 1.865,0.396 0.385,0.25 1.479,1.854 1.865,2.104 0.385,0.25 1.323,1.729 1.75,1.302 true 2.271,0.521 1.646,1.281 true 1.021,0.875 1.531,1.271 true 1.875,1.281 2.302,0.854 true 1.896,1.427 2.354,1.646 true 1.604,0.177 1.792,0.354 0.188,0.177 10 false a1 1.542,1.896 1.844,2.063 0.302,0.167 10 false aG1 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a 0.24,2.125 0.448,2.281 0.208,0.156 10 false *b 2.292,0.698 2.729,0.854 0.438,0.156 10 false ADPG 0.604,0.76 1,0.927 0.396,0.167 10 false VAR+ 2.167,0.323 2.563,0.49 0.396,0.167 10 false VAL+ 1.094,1.698 1.385,1.865 0.292,0.167 10 false VA- 2.208,1.688 2.656,1.854 0.448,0.167 10 false AGND
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Vehicle Wire Harness)


Disconnect the aG1 vehicle wire harness connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-10 (ADPG) - aG1-5 Always Below 1 Ω
a1-7 (VAR+) - aG1-6 Always Below 1 Ω
a1-8 (VAL+) - aG1-13 Always Below 1 Ω
a1-9 (VA-) - aG1-7 Always Below 1 Ω
a1-12 (AGND) - aG1-14 Always Below 1 Ω
a1-10 (ADPG) - Body ground Always 10 kΩ or higher
a1-7 (VAR+) - Body ground Always 10 kΩ or higher
a1-8 (VAL+) - Body ground Always 10 kΩ or higher
a1-9 (VA-) - Body ground Always 10 kΩ or higher
a1-12 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO WIRE - NAVIGATION RECEIVER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO WIRE - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the aG1 radio wire connector.


b.

Disconnect the G113 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
aG1-5 - G113-25 (ADPG) Always Below 1 Ω
aG1-6 - G113-26 (VAR+) Always Below 1 Ω
aG1-13 - G113-28 (VAL+) Always Below 1 Ω
aG1-7 - G113-27 (VA-) Always Below 1 Ω
aG1-14 - G113-11 (AGND) Always Below 1 Ω
aG1-5 - Body ground Always 10 kΩ or higher
aG1-6 - Body ground Always 10 kΩ or higher
aG1-13 - Body ground Always 10 kΩ or higher
aG1-7 - Body ground Always 10 kΩ or higher
aG1-14 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR