Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is ACC, 1 or more times, the radio and display receiver assembly cannot receive the signal for 30 seconds or more
·

Harness or connector

·

Combination meter assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E299675E05
1.167,2.365 4.833,2.563 3.667,0.198 10 false : Local CAN Communication Line 1.708,0.51 2.323,0.708 0.615,0.198 10 false LCL+ 2.156,0.354 2.469,0.552 0.313,0.198 10 false 38 2.167,0.958 2.479,1.156 0.313,0.198 10 false 37 1.74,1.104 2.354,1.302 0.615,0.198 10 false LCL- 5.094,0.5 5.708,0.698 0.615,0.198 10 false CNH1 5.094,1.115 5.708,1.313 0.615,0.198 10 false CNL1 4.865,0.344 5.021,0.542 0.156,0.198 10 false 3 4.865,0.958 5.021,1.156 0.156,0.198 10 false 4 0.802,1.667 1.26,1.865 0.458,0.198 10 false G9 0.802,1.844 4.781,2.042 3.979,0.198 10 false Combination Meter Assembly 4.76,1.667 5.375,1.865 0.615,0.198 10 false G38 4.771,1.844 6.49,2.25 1.719,0.406 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G38 radio and display receiver assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-3 (CNH1) - G9-38 (LCL+) Always Below 1 Ω
G38-4 (CNL1) - G9-37 (LCL-) Always Below 1 Ω
G38-3 (CNH1) or G9-38 (LCL+) - Body ground Always 10 kΩ or higher
G38-4 (CNL1) or G9-37 (LCL-) - Body ground Always 10 kΩ or higher
G38-3 (CNH1) - G38-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G38-3 (CNH1) - Body ground Always Below 1 V
G38-4 (CNL1) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.
E317642N01
0.583,1.792 0.729,1.792 0.729,1.792 0.906,1.313 true 1.292,1.792 1.167,1.792 1.167,1.792 1.052,1.313 true 0.219,1.719 0.833,1.917 0.615,0.198 10 false LCL+ 1.344,1.698 1.958,1.896 0.615,0.198 10 false LCL-

Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
38 (LCL+) - 37 (LCL-) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E317643N01
1.333,1.875 1.5,1.875 1.5,1.875 2.104,1.177 true 2.354,1.875 2.146,1.875 2.146,1.875 2.25,1.177 true 2.417,1.792 3.031,1.99 0.615,0.198 10 false CNH1 0.958,1.792 1.573,1.99 0.615,0.198 10 false CNL1

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK METER / GAUGE SYSTEM

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK METER / GAUGE SYSTEM
a.

Turn the ignition switch to ON and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio and visual system can be operated normally.

OK:

Audio system returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY