Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER(for 2WD)
RM3250E _53 Suspension _038041 FRONT SUSPENSION _0182535 FRONT SHOCK ABSORBER(for 2WD) A

FRONT SUSPENSION  FRONT SHOCK ABSORBER(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48132 1.INSTALL FRONT COIL SPRING LH

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

For SST with stopper pins:

i.

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00022, 09727-00031)


ii.
C302414C01
2.563,1.885 2.198,1.656 false 2.563,2.052 2.563,1.885 2.563,1.885 2.875,1.615 false 2.49,4.354 2.49,4.198 2.49,4.198 2.865,3.958 false 2.5,4.198 2.115,3.958 false 1.583,0.26 1.896,0.417 0.313,0.156 10 false *a 1.615,2.573 1.927,2.729 0.313,0.156 10 false *b 2.5,2.063 2.813,2.219 0.313,0.156 10 false *c 2.417,4.365 2.729,4.521 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.
C302415C01
1.469,1.469 1.469,1.01 false 3.135,1.479 3.135,1.021 false 0.219,0.063 0.531,0.219 0.313,0.156 10 false *a 1.76,0.073 2.073,0.229 0.313,0.156 10 false *b 1.406,1.479 1.719,1.635 0.313,0.156 10 false *c 3.073,1.49 3.385,1.646 0.313,0.156 10 false *c
*a Correct
*b Incorrect
*c Stopper Pin


Install the stopper pins to the hooks of SST.

CAUTION:

Make sure that the stopper pins are installed securely.



iv.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.

·
C297651N01
0.917,1.854 1.25,1.854 true 0.625,1.792 0.99,1.948 0.365,0.156 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure. In this case, installing the coil spring stopper belt as shown in the illustration is recommended.



SST
09727-00110  



b.
C288500N06
2.406,1.26 2.406,0.969 2.406,0.969 2.667,0.969 false 2.698,0.896 3.156,1.094 0.458,0.198 10 false SST

For SST without stopper pins:

i.

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


ii.
C302414C01
2.563,1.885 2.198,1.656 false 2.563,2.052 2.563,1.885 2.563,1.885 2.875,1.615 false 2.49,4.354 2.49,4.198 2.49,4.198 2.865,3.958 false 2.5,4.198 2.115,3.958 false 1.583,0.26 1.896,0.417 0.313,0.156 10 false *a 1.615,2.573 1.927,2.729 0.313,0.156 10 false *b 2.5,2.063 2.813,2.219 0.313,0.156 10 false *c 2.417,4.365 2.729,4.521 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.



HINT:
C297652N01
0.896,1.854 1.26,1.854 true 0.615,1.781 0.927,1.938 0.313,0.156 10 false SST

Installing SST as shown in the illustration is recommended.


SST
09727-00110  



c.
C322793C01
0,0 0,0 false
V100135

Recess


Install the coil spring to the front shock absorber assembly LH. Fit the lower end of the coil spring into the recess of the spring lower seat.


Hide 48157C 2.INSTALL FRONT UPPER COIL SPRING INSULATOR LH

a.

Install the front coil spring upper insulator LH to the front shock absorber assembly LH.


Hide 48609 3.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the front shock absorber cushion retainer to the front shock absorber assembly LH.


b.

Install the front suspension support sub-assembly LH to the front shock absorber assembly LH.


Hide 48510J 4.INSTALL FRONT NO. 1 SHOCK ABSORBER CUSHION

a.

Install the front No. 1 shock absorber cushion to the front shock absorber assembly LH.


Hide 48510Q 5.INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER

a.

Install the front shock absorber cushion retainer to the front shock absorber assembly LH.


Hide 48680A 6.INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C113158C01
0.833,1.427 0.833,1.802 false 2.344,1.083 2.344,1.844 true 0.25,0.125 0.479,0.365 0.229,0.24 10 false *a 2.938,0.094 3.167,0.333 0.229,0.24 10 false *c 1.604,0.01 1.833,0.25 0.229,0.24 10 false *b 0.76,1.896 0.99,2.135 0.229,0.24 10 false *1 2.281,1.906 2.521,2.146 0.24,0.24 10 false *2
*1 Front Suspension Support Sub-assembly
*2 Absorber Bush
*a for LH
*b Front of the Vehicle
*c for RH


Align the front suspension support sub-assembly and absorber bushes as shown in the illustration.


b.
C323461C01
1.719,2.354 2.031,2.552 0.313,0.198 10 false *a 1.104,2.906 1.417,3.104 0.313,0.198 10 false *b 1.031,0.896 1.344,1.094 0.313,0.198 10 false *c
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Using a ball joint lock nut wrench, install a new lock nut.

Torque:
Specified tightening torque : 18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 12 N*m (122 kgf*cm, 9 ft.*lbf)




c.

Release the coil spring while checking the position of the spring lower seat and suspension support.


Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C330033C01
1.458,3.938 1.875,3.938 false 0.552,3.969 0.802,3.969 0.802,3.969 0.885,4.219 false 2.073,1.958 2.385,2.156 0.313,0.198 10 false *a 0.365,3.875 0.677,4.073 0.313,0.198 10 false *b 1.958,3.833 2.271,4.031 0.313,0.198 10 false *c
*a Torque Wrench Fulcrum Length
*b 12 x 14 mm Long Offset Wrench
*c 12 mm Socket Hexagon Wrench


Using a 12 mm socket hexagon wrench and 12 x 14 mm long offset wrench, install the 3 nuts to the upper side of the shock absorber with coil spring.

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a long offset wrench (fulcrum length of 206.25 mm (8.1201 in.)) + torque wrench (fulcrum length of 380 mm (14.9606 in.)): 25.9 N*m (264 kgf*cm, 19 ft.*lbf)




b.
C322786

Temporarily install the bolt and nut as shown in the illustration.

HINT:

Fix the nut in place and temporarily install the bolt.



Hide 89543 9.CONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.
C322785

Connect the front speed sensor LH with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 47313J 10.CONNECT FRONT FLEXIBLE HOSE

a.
C322784

Connect the front flexible hose with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 11.INSTALL FRONT WHEEL

Hide 12.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Press down on the vehicle several times to stabilize the suspension.


Hide 13.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT