Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER(for 2WD)
RM3250E _53 Suspension _038041 FRONT SUSPENSION _0182535 FRONT SHOCK ABSORBER(for 2WD) A

FRONT SUSPENSION  FRONT SHOCK ABSORBER(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front shock absorber removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment
·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


VSC malfunctioning (Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 47313J 2.DISCONNECT FRONT FLEXIBLE HOSE

a.
C322784

Remove the bolt and disconnect the front flexible hose.


Hide 89543 3.DISCONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.
C322785

Remove the bolt and disconnect the front speed sensor LH.


Hide 4.REMOVE FRONT UPPER SUSPENSION ARM

Hide 5.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

C322786

a.

Remove the nut and bolt.

HINT:

While fixing the nut in place, loosen and remove the bolt.



b.
C322787

Remove the 3 nuts and front shock absorber with coil spring.


Hide 48680A 6.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

For SST with stopper pins:

i.

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00022, 09727-00031)


ii.
C298400C01
2.615,2.031 2.615,1.875 2.615,1.875 2.938,1.74 false 2.625,1.875 2.26,1.74 false 2.542,4.177 2.542,4.021 2.542,4.021 2.906,3.875 false 2.542,4.021 2.167,3.875 false 1.531,0.26 1.844,0.417 0.313,0.156 10 false *a 1.604,2.563 1.917,2.719 0.313,0.156 10 false *b 2.552,2.042 2.865,2.198 0.313,0.156 10 false *c 2.469,4.188 2.781,4.344 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.
C302415C01
1.469,1.469 1.469,1.01 false 3.135,1.479 3.135,1.021 false 0.219,0.063 0.531,0.219 0.313,0.156 10 false *a 1.76,0.073 2.073,0.229 0.313,0.156 10 false *b 1.406,1.479 1.719,1.635 0.313,0.156 10 false *c 3.073,1.49 3.385,1.646 0.313,0.156 10 false *c
*a Correct
*b Incorrect
*c Stopper Pin


Install the stopper pins to the hooks of SST.

CAUTION:

Make sure that the stopper pins are installed securely.



iv.
C322788C01
2.667,1.156 2.875,1.281 2.875,1.281 3.042,1.281 false 2.448,1.354 2.656,1.479 2.656,1.479 2.823,1.479 false 0.667,1.542 1,1.542 1,1.542 2,1.385 true 3.115,1.167 3.427,1.365 0.313,0.198 10 false *a 2.875,1.385 3.427,1.594 0.552,0.208 10 false SST 0.271,1.438 0.781,1.625 0.51,0.188 10 false SST
*a Vehicle Nut


Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


v.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.

·
C322790N01
0.708,1.844 1.875,1.844 true 0.375,1.771 0.833,1.969 0.458,0.198 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure. In this case, installing the coil spring stopper belt as shown in the illustration is recommended.



SST
09727-00110  



b.

For SST without stopper pins:

i.
C288500N22
2.406,1.26 2.406,0.969 2.406,0.969 2.667,0.969 false 2.698,0.896 3.156,1.094 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


ii.
C298400C01
2.615,2.031 2.615,1.875 2.615,1.875 2.938,1.74 false 2.625,1.875 2.26,1.74 false 2.542,4.177 2.542,4.021 2.542,4.021 2.906,3.875 false 2.542,4.021 2.167,3.875 false 1.531,0.26 1.844,0.417 0.313,0.156 10 false *a 1.604,2.563 1.917,2.719 0.313,0.156 10 false *b 2.552,2.042 2.865,2.198 0.313,0.156 10 false *c 2.469,4.188 2.781,4.344 0.313,0.156 10 false *d
*a Correct
*b Incorrect
*c Parallel
*d Not Parallel


Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·

Make sure that the hooks of the upper and lower arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

Make sure that the arms of SST are parallel and attached to the coil spring, and the number of coil springs between the hooks on each side is the same.

·

Check that the claws of the hooks are securely attached to the coil spring.




iii.
C322789C01
2.646,1.156 2.802,1.344 2.802,1.344 3.052,1.344 false 2.417,1.417 2.573,1.604 2.573,1.604 2.823,1.604 false 0.552,1.531 0.885,1.531 0.885,1.531 2.01,1.375 true 3.115,1.26 3.427,1.458 0.313,0.198 10 false *a 2.896,1.531 3.313,1.729 0.417,0.198 10 false SST 0.208,1.448 0.625,1.646 0.417,0.198 10 false SST
*a Vehicle Nut


Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


iv.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends while using SST, stop immediately and reattach SST correctly.

·

Do not compress the coil spring to the point where the coils touch each other.

·

Do not use an impact wrench.



HINT:
C322791N01
0.719,1.865 1.885,1.865 true 0.385,1.781 0.844,1.979 0.458,0.198 10 false SST

Installing SST as shown in the illustration is recommended.


SST
09727-00110  



c.
C322792

Hold the shock absorber rod and remove the nut.

CAUTION:

Do not remove the nut when the coil spring is not free.



Hide 48510Q 7.REMOVE FRONT SHOCK ABSORBER CUSHION RETAINER

a.

Remove the front shock absorber cushion retainer from the front shock absorber assembly LH.


Hide 48510J 8.REMOVE FRONT NO. 1 SHOCK ABSORBER CUSHION

a.

Remove the front No. 1 shock absorber cushion from the front shock absorber assembly LH.


Hide 48609 9.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Remove the front suspension support sub-assembly LH from the front shock absorber assembly LH.


b.

Remove the front shock absorber cushion retainer from the front shock absorber assembly LH.


Hide 48157C 10.REMOVE FRONT UPPER COIL SPRING INSULATOR LH

a.

Remove the front coil spring upper insulator LH from the front coil spring LH.


Hide 48132 11.REMOVE FRONT COIL SPRING LH

a.

Remove the front coil spring LH from the front shock absorber assembly LH.