Home › Engine / Hybrid System › 1TR-FE FUEL › FUEL SENDER GAUGE ASSEMBLY
RM3250E _51 Engine / Hybrid System _037999 1TR-FE FUEL _0182615 FUEL SENDER GAUGE ASSEMBLY G

1TR-FE FUEL  FUEL SENDER GAUGE ASSEMBLY  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY

a.

Check the fuel sender gauge assembly output voltage.

i.
A349952C01
2.219,0.667 2.615,0.667 true 1.719,0.615 2.115,0.26 2.115,0.26 2.26,0.26 true 0.042,0.042 0.26,0.25 0.219,0.208 10 false *a 1.615,1.74 1.823,1.938 0.208,0.198 10 false *b 2.656,0.583 2.875,0.802 0.219,0.219 10 false FV 2.302,0.188 2.521,0.406 0.219,0.219 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.

Measure the voltage according to the value(s) in the table below.

A359635C01
0.917,2.583 1.385,2.583 true 0.917,1.25 1.458,1.25 true 3.917,2.5 4.438,2.5 true 3.917,1.5 4.469,1.5 true 2.417,0.5 2.583,0.5 2.583,0.5 2.875,0.542 true 3.292,0.5 3.833,0.333 3.833,0.333 4,0.333 true 0.5,0.833 0.813,0.99 0.313,0.156 10 false *A 3.667,0.833 3.979,0.99 0.313,0.156 10 false *B 2.271,0.083 2.583,0.24 0.313,0.156 10 false *a 0.781,1.167 0.938,1.365 0.156,0.198 10 false F 0.792,2.5 0.948,2.698 0.156,0.198 10 false E 3.781,2.417 3.938,2.615 0.156,0.198 10 false E 3.781,1.417 3.938,1.615 0.156,0.198 10 false F 2.188,0.417 2.5,0.615 0.313,0.198 10 false FR 4.021,0.25 4.333,0.448 0.313,0.198 10 false FE
*A for Long Wheelbase *B for Short Wheelbase
*a Component without harness connected
(Fuel Sender Gauge Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.25 to 4.61 V*
Float position is E (lower) 0.34 to 0.70 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage (F) = (0.850 x Voltage applied to terminals) to (0.922 x Voltage applied to terminals)

·

Output voltage (E) = (0.068 x Voltage applied to terminals) to (0.140 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.