When the engine is cranked, the ST NO.1 relay drive signal output from the ignition switch assembly is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN NO.1 relay by turning Tr1 on. Then, the fuel pump operates.
While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
| Result | Proceed to |
|---|---|
| Fuel pump operating sound does not occur
(w/o Entry and Start System) |
A |
| Fuel pump operating sound does not occur
(w/ Entry and Start System) |
B |
| Fuel pump operating sound occurs | C |
A
B
C
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Disconnect the instrument panel junction block assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2G-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the C/OPN NO. 1 relay.
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2P-8 - G45-5 (FC) | Always | Below 1 Ω |
| 2P-8 or G45-5 (FC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2K-5 - O6-4 | Always | Below 1 Ω |
| 2K-5 or O6-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O6-5 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect fuel pump.
For long wheelbase
Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL PUMP(for Long Wheelbase)>INSPECTION
for short wheelbase
Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL PUMP(for Short Wheelbase)>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for long wheelbase) | B |
| NG (for short wheelbase) | C |
A
B
C
Disconnect the ignition switch assembly connector.
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (IG2) - 2G-1 | Always | Below 1 Ω |
| G1-3 (IG2) or 2G-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Condition | Starter Signal |
|---|---|
| Ignition switch ON | OFF |
| Engine Started | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the values displayed on the GTS while cranking.
Values are displayed continuously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG