Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _038021 2TR-FE ENGINE CONTROL _0182708 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0412  Secondary Air Injection System Switching Valve "A" Circuit  


DESCRIPTION

The secondary air injection system injects air into the exhaust port of the cylinder head using an electric air pump, starting when the engine is started cold and operating until the catalyst warms up, in order to promote combustion of unburned fuel and decrease the amount of hydrocarbons (HC) and carbon monoxide (CO) in the exhaust gas.

A121746E12
3.25,2.896 3.385,3.323 true 3.458,2.656 4.396,3.531 true 4.438,1.281 4.052,2.031 true 4.927,1.719 5.208,1.479 false 1.323,1.375 2.094,1.292 false 2.104,1.292 1.74,1.427 false 2.542,1.979 2.313,2.354 false 0.531,0.344 0.698,0.719 false 0.042,0.167 0.719,0.573 0.677,0.406 10 false Diagnostic Signal 1.333,0.625 1.792,0.823 0.458,0.198 10 false ECM 2.177,1.229 4.323,1.427 2.146,0.198 10 false Command Signal 3.729,0.646 6.021,0.844 2.292,0.198 10 false Pressure Signal 4.135,1.094 7.042,1.292 2.906,0.198 10 false Air Pressure Sensor 5.281,1.354 6.719,1.573 1.438,0.219 10 false Air Pump Drive Signal 6.271,2.083 6.688,2.281 0.417,0.198 10 false Filter 5.521,3.406 6.219,3.656 0.698,0.25 10 false Air Pump 0.448,2.146 1.677,2.552 1.229,0.406 10 false Air Injection Control Driver 1.74,2.396 2.99,2.813 1.25,0.417 10 false Air Switching Valve Drive Signal 3.094,3.333 4.625,3.531 1.531,0.198 10 false Reed Valve 3.979,3.542 6.885,3.74 2.906,0.198 10 false Air Switching Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0412 Secondary Air Injection System Switching Valve "A" Circuit Condition 1:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system not operating (air pump OFF, air switching valve OFF)

2.

Diagnostic signal from air injection control driver 40%

3.

Battery voltage 8 V or more



Condition 2:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system operating (air pump ON, air switching valve ON)

2.

Diagnostic signal from air injection control driver 40%

3.

Battery voltage 8 V or more



Condition 1:
·

Open in air switching valve drive circuit

·

Short between air switching valve drive circuit and +B circuit

·

Air injection control driver

·

Air switching valve assembly

·

ECM


Condition 2:
·

Short between air switching valve drive circuit and body ground

·

Air injection control driver

·

Air switching valve assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The Air Injection Control Driver (AID) detects open and short circuits according to the voltages of the air pump terminal and the Air Switching Valve (ASV) terminal, and transmits diagnostic information as a signal to the ECM.

For a short time after cold engine starts, the ECM transmits command signals to the AID to drive the air pump and ASV.

The AID transmits an ASV malfunction signal to the ECM if either of the following conditions is met:

·

The voltage at the AID terminal relating to the ASV is low despite the AID receiving command signals from the ECM to drive the ASV.

·

The voltage at the AID terminal relating to the ASV is high despite the AID receiving no command signals from the ECM to drive the ASV.


The ECM stores the DTC based on diagnostic signals from the AID.

MONITOR STRATEGY

Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air switching valve assembly
Frequency of Operation Once per drive cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing Next.

12.

Perform the following to confirm the secondary air injection system pending DTCs: Press Exit button.

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0412.

16.

Check the DTC judgment result.

GTS Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


WIRING DIAGRAM

A348504E02
5.948,0.813 6.563,1.01 0.615,0.198 10 false AIRV 5.938,1.573 6.552,1.771 0.615,0.198 10 false AIRP 5.938,2.354 6.552,2.552 0.615,0.198 10 false AIDI 5.594,0.896 6.052,1.094 0.458,0.198 10 false G46 5.729,0.708 5.885,0.906 0.156,0.198 10 false 5 5.583,1.667 6.042,1.865 0.458,0.198 10 false G46 5.74,1.49 5.896,1.688 0.156,0.198 10 false 6 5.594,2.448 6.052,2.646 0.458,0.198 10 false G45 5.677,2.271 5.99,2.469 0.313,0.198 10 false 20 4.802,0.896 5.115,1.094 0.313,0.198 10 false C69 4.844,0.729 5,0.927 0.156,0.198 10 false 3 4.813,1.656 5.125,1.854 0.313,0.198 10 false C69 4.844,1.469 5,1.667 0.156,0.198 10 false 4 4.813,2.438 5.125,2.635 0.313,0.198 10 false C69 4.844,2.271 5,2.469 0.156,0.198 10 false 2 4.823,3.01 5.135,3.208 0.313,0.198 10 false C69 4.854,2.844 5.01,3.042 0.156,0.198 10 false 5 4.479,0.781 4.938,0.979 0.458,0.198 10 false SIV 4.531,1.521 4.99,1.719 0.458,0.198 10 false SIP 4.625,2.344 4.938,2.542 0.313,0.198 10 false DI 4.552,2.99 4.865,3.188 0.313,0.198 10 false +B 2.948,0.74 3.563,0.938 0.615,0.198 10 false BATT 2.969,1.396 3.281,1.594 0.313,0.198 10 false VV 2.958,2.01 3.271,2.208 0.313,0.198 10 false VP 3.021,3.354 4.729,3.635 1.708,0.281 10 false Air Injection Control Driver 2.958,2.729 3.115,2.927 0.156,0.198 10 false E 2.635,0.813 3.094,1.01 0.458,0.198 10 false A33 2.625,1.458 3.083,1.656 0.458,0.198 10 false C69 2.625,2.094 3.083,2.292 0.458,0.198 10 false A33 2.625,2.729 2.938,2.927 0.313,0.198 10 false C69 2.771,0.635 2.927,0.833 0.156,0.198 10 false 1 2.76,1.281 2.917,1.479 0.156,0.198 10 false 6 2.76,1.906 2.917,2.104 0.156,0.198 10 false 2 2.771,2.552 2.927,2.75 0.156,0.198 10 false 1 0.906,1.781 1.365,1.979 0.458,0.198 10 false C71 0.875,1.948 1.698,2.542 0.823,0.594 10 false Air Switching Valve 1.823,3.385 2.281,3.583 0.458,0.198 10 false A14 1.823,3.583 3.052,3.781 1.229,0.198 10 false Air Pump 0.469,3.479 1.385,3.677 0.917,0.198 10 false AIR PMP 0.583,1.813 0.74,2.01 0.156,0.198 10 false 2 0.573,2.479 0.729,2.677 0.156,0.198 10 false 1 1.563,3.281 1.719,3.479 0.156,0.198 10 false 2 1.542,3.823 1.698,4.021 0.156,0.198 10 false 4 0.448,6.063 1.521,6.26 1.073,0.198 10 false FL MAIN 0.656,6.99 1.729,7.188 1.073,0.198 10 false Battery 1.094,5.375 1.865,5.573 0.771,0.198 10 false J/B-B 3.125,6.427 4.719,7.042 1.594,0.615 10 false Instrument Panel Junction Block Assembly 3.396,5.938 5.542,6.135 2.146,0.198 10 false EFI-MAIN NO. 1 2.292,5.219 2.604,5.417 0.313,0.198 10 false 2B 2.313,5.042 2.469,5.24 0.156,0.198 10 false 1 2.719,6.208 3.031,6.406 0.313,0.198 10 false 2J 3.01,6.198 3.167,6.396 0.156,0.198 10 false 5 2.5,5.385 4.646,5.583 2.146,0.198 10 false EFI-MAIN NO. 1 2.875,4.75 4.25,4.948 1.375,0.198 10 false EFI NO. 1 4.448,5.635 4.76,5.833 0.313,0.198 10 false 2P 4.521,5.448 4.677,5.646 0.156,0.198 10 false 9 4.448,4.365 4.76,4.563 0.313,0.198 10 false 2N 4.521,4.188 4.677,4.385 0.156,0.198 10 false 1 5.917,5.625 6.531,5.823 0.615,0.198 10 false MREL 5.594,5.625 6.052,5.823 0.458,0.198 10 false G45 5.719,5.448 5.875,5.646 0.156,0.198 10 false 6 5.938,6.083 6.25,6.281 0.313,0.198 10 false E1 5.594,6.083 6.052,6.281 0.458,0.198 10 false C52 5.74,5.927 5.896,6.125 0.156,0.198 10 false 3 6.26,6.896 6.719,7.094 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR SWITCHING VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)
a.

Disconnect the air switching valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C71-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the air switching valve connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C71-2 - C69-6 (VV) Always Below 1 Ω
C71-2 or C69-6 (VV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR