Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2015.06–2016.01
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182720 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E324883E01
0.844,1.417 1.302,1.615 0.458,0.198 10 false ECM 0.417,3.25 2,3.719 1.583,0.469 10 false G69 0.417,3.406 2,3.875 1.583,0.469 10 false Certification ECU (Smart Key ECU Assembly)*5 1.281,2.719 2.865,3.188 1.583,0.469 10 false SPD 1.677,2.729 3.26,3.198 1.583,0.469 10 false 7 5.635,4.542 6.188,4.875 0.552,0.333 10 false SPD1 5.656,2.719 6.208,3.052 0.552,0.333 10 false SPD 1.26,4.573 1.813,4.906 0.552,0.333 10 false SPD 5.646,0.875 6.198,1.208 0.552,0.333 10 false +S 1.25,0.875 1.802,1.208 0.552,0.333 10 false SPD 1.698,0.979 2.25,1.313 0.552,0.333 10 false G88 2.125,0.979 2.677,1.313 0.552,0.333 10 false G45 2.563,0.979 3.115,1.313 0.552,0.333 10 false G85 2.979,0.979 3.531,1.313 0.552,0.333 10 false G83 1.688,0.771 2.24,1.104 0.552,0.333 10 false 12*1 2.115,0.781 2.667,1.115 0.552,0.333 10 false 23*2 2.531,0.781 3.083,1.115 0.552,0.333 10 false 10*3 2.969,0.771 3.521,1.104 0.552,0.333 10 false 17*4 5.375,0.885 5.927,1.219 0.552,0.333 10 false 19 5.25,1.406 7.083,1.625 1.833,0.219 10 false G9 5.25,1.563 7.083,1.781 1.833,0.219 10 false Combination Meter Assembly 0.354,5.083 1.938,5.552 1.583,0.469 10 false G117 0.365,5.271 1.948,5.74 1.583,0.469 10 false Radio Receiver Assembly 1.688,4.573 3.271,5.042 1.583,0.469 10 false 17 5.375,4.552 6.135,5.01 0.76,0.458 10 false 25 5.448,2.719 6.208,3.177 0.76,0.458 10 false 5 5.854,3.26 6.615,3.719 0.76,0.458 10 false G27 5.854,3.417 6.771,3.906 0.917,0.49 10 false Body ECU*6 5.906,5.104 6.823,5.594 0.917,0.49 10 false G90 5.917,5.271 6.833,5.76 0.917,0.49 10 false TCM*4, *7 0.25,5.646 2.24,5.844 1.99,0.198 10 false *1: for 1GR-FE 0.25,5.917 2.24,6.115 1.99,0.198 10 false *2: for 1TR-FE, 2TR-FE 0.25,6.208 2.24,6.406 1.99,0.198 10 false *3: for 1GD-FTV, 2GD-FTV 0.25,6.49 2.24,6.688 1.99,0.198 10 false *4: for 1KD-FTV, 2KD-FTV 2.198,5.635 4.188,5.833 1.99,0.198 10 false *5: w/ Entry and Start System 2.208,5.917 5.802,6.115 3.594,0.198 10 false *6: w/ Speed-sensitive Automatic Door Lock Function 2.198,6.208 5.781,6.51 3.583,0.302 10 false *7: for Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C39
1.479,0.438 1.896,0.656 0.417,0.219 0.656,1.802 0.865,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.458 1.906,0.656 0.313,0.198 10 false G9 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.583 3.188,3.854 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal G9-19 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G9-19 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Speed-sensitive Automatic Door Lock Function

*7: for Automatic Transmission


a.

Disconnect the G117 radio receiver assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G27 body ECU connector.*6


f.

Disconnect the G90 TCM connector.*4, *7


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-17 (SPD) - G9-19 (+S) Always Below 1 Ω
G117-17 (SPD) or G9-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR