Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P007C  Charge Air Cooler Temperature Sensor Circuit Low  P007D  Charge Air Cooler Temperature Sensor Circuit High  


DESCRIPTION

A208462E13
1.49,2 1.646,1.76 1.646,1.76 1.792,1.76 false 0.208,0.146 0.813,0.406 0.604,0.26 10 false (Fig. 1) 0.208,0.542 1.375,0.865 1.167,0.323 10 false Resistance kΩ 1.823,1.677 2.74,2.031 0.917,0.354 10 false Acceptable 1.208,4.063 2.604,4.375 1.396,0.313 10 false Temperature °C (°F)

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


- DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P007C Intake Air Temp (Turbo)
P007D

HINT:

If DTC P007C or P007D is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power



CONFIRMATION DRIVING PATTERN

P007C, P007D
DTC Detection Drive Pattern Ignition switch to ON for 1 second

WIRING DIAGRAM

A337317E10
0.448,2.635 0.76,2.833 0.313,0.198 10 false C73 5.729,3.01 6.188,3.208 0.458,0.198 10 false C55 5.74,3.208 6.198,3.406 0.458,0.198 10 false ECM 0.438,2.833 2.969,3.052 2.531,0.219 10 false Intake Air Temperature Sensor (Turbo) 5.26,1.313 5.719,1.51 0.458,0.198 10 false THIA 5.26,1.917 5.781,2.115 0.521,0.198 10 false E2 2.198,1.292 2.656,1.49 0.458,0.198 10 false 2 2.198,1.896 2.656,2.094 0.458,0.198 10 false 1 4.99,1.302 5.448,1.5 0.458,0.198 10 false 20 4.99,1.917 5.448,2.115 0.458,0.198 10 false 28 5.906,0.948 6.365,1.146 0.458,0.198 10 false 5 V 5.854,1.219 6.313,1.417 0.458,0.198 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 234 854

d.

Read the value.

OK:

Same as air temperature near intake manifold


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204915C21
0.615,3.625 1.021,3.875 0.406,0.25 0.667,0.385 0.885,0.563 0.219,0.177 10 false *1 2.646,0.354 2.906,0.552 0.26,0.198 10 false *2 2.365,1.354 2.719,1.521 0.354,0.167 10 false THIA 2.417,1.833 2.698,2.01 0.281,0.177 10 false E2 0.719,3.26 0.917,3.417 0.198,0.156 10 false *a 0.688,3.667 0.979,3.823 0.292,0.156 10 false C73
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor [Turbo])


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 234 854

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C73-2 - C55-20 (THIA) Always Below 1 Ω
C73-1 - C55-28 (E2) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C11
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.406,1.031 2.719,1.229 0.313,0.198 10 false THIA 2.438,1.51 2.75,1.708 0.313,0.198 10 false E2
*1 Intake Air Temperature Sensor (turbo)
*2 ECM


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 234 854

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR [TURBO] - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR [TURBO] - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C73-2 or C55-20 (THIA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED