The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the common rail pressure so that it reaches the target pressure determined by the ECM. The pressure sensor is a semiconductor that varies its electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the common rail fuel pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0191 | Fuel Rail Pressure Sensor Circuit Range / Performance | The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0191 | ·
Common Rail Pressure ·
Target Common Rail Pressure |
| DTC Detection Drive Pattern | Idling for 1 second |
Refer to DTC P0087 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0087).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Common Rail Pressure and Target Common Rail Pressure.
| Tester Display |
|---|
| Target Common Rail Pressure |
| Common Rail Pressure |
Start the engine.
Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.
| Result | Proceed to |
|---|---|
| Common Rail Pressure is always 10000 kPa or less
or Common Rail Pressure is always 200000 kPa or higher |
A |
| Except above | B |
Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".
A
B
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C120-5 (PR) - C55-26 (PCR1) | Always | Below 1 Ω |
| C120-2 (PR2) - C55-33 (PCR2) | Always | Below 1 Ω |
| C120-1 (VCS) - C56-2 (VCS) | Always | Below 1 Ω |
| C120-6 (VC) - C55-18 (VC) | Always | Below 1 Ω |
| C120-4 (E2) - C55-28 (E2) | Always | Below 1 Ω |
| C120-3 (E2S) - C56-1 (E2S) | Always | Below 1 Ω |
| C120-5 (PR) or C55-26 (PCR1) - Body ground | Always | 10 kΩ or higher |
| C120-2 (PR2) or C55-33 (PCR2) - Body ground | Always | 10 kΩ or higher |
| C120-1 (VCS) or C56-2 (VCS) - Body ground | Always | 10 kΩ or higher |
| C120-6 (VC) or C55-18 (VC) - Body ground | Always | 10 kΩ or higher |
| C120-4 (E2) or C55-28 (E2) - Body ground | Always | 10 kΩ or higher |
| C120-3 (E2S) or C56-1 (E2S) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0191 is output | A |
| No DTC is output | B |
A
B
Replace the common rail.
Click hereEngine / Hybrid System>1KD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0191 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT