Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0200  Injector Circuit / Open  


DESCRIPTION

The injector driver delivers drive signals to the injector assemblies using the DC/DC converter, which provides a high-voltage and quick-charging system.

Soon after the injector driver receives a fuel injection command (#1 to #4) signal from the ECM, the injector driver responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.

A221606E41
2.042,5.75 2.458,5.969 0.417,0.219 4.365,5.75 4.781,5.969 0.417,0.219 3.281,5.75 3.698,5.969 0.417,0.219 3.281,0.167 4.188,0.427 0.906,0.26 10 false Injector Driver 2.604,1.135 3.271,1.531 0.667,0.396 10 false DC/DC Converter 0.438,1.333 1.396,1.604 0.958,0.271 10 false from Battery 0.323,2.198 1.448,2.427 1.125,0.229 10 false Command Pulse 0.906,4.615 2.125,4.885 1.219,0.271 10 false Confirmation Pulse 0.177,5.688 1.781,5.917 1.604,0.229 10 false Injector Driver Connector 0.073,0.146 2.01,0.396 1.938,0.25 10 false Injector Driver Wiring Diagram 0.698,3.448 1.073,3.667 0.375,0.219 10 false ECM 1.552,2.51 1.813,2.719 0.26,0.208 10 false #1 1.552,2.802 1.792,3.01 0.24,0.208 10 false #4 1.552,3.125 1.813,3.333 0.26,0.208 10 false #2 1.552,3.427 1.792,3.625 0.24,0.198 10 false #3 1.49,4.031 1.875,4.229 0.385,0.198 10 false INJF 1.49,3.729 1.875,3.948 0.385,0.219 10 false PRD 5.052,2.469 5.385,2.708 0.333,0.24 10 false IJ1- 5.031,0.594 5.458,0.823 0.427,0.229 10 false RLF+ 5.063,0.927 5.458,1.146 0.396,0.219 10 false IJ3+ 5.063,1.229 5.427,1.458 0.365,0.229 10 false IJ2+ 5.063,1.531 5.396,1.729 0.333,0.198 10 false IJ4+ 5.052,1.844 5.385,2.063 0.333,0.219 10 false IJ1+ 5.052,2.792 5.396,3.01 0.344,0.219 10 false IJ4- 5.031,3.083 5.385,3.323 0.354,0.24 10 false IJ2- 5.031,3.396 5.344,3.656 0.313,0.26 10 false IJ3- 5.031,3.74 5.458,3.979 0.427,0.24 10 false RLF- 3.24,3.104 3.75,3.531 0.51,0.427 10 false Control Circuit 3.615,5.427 4,5.646 0.385,0.219 10 false GND 1.021,7.396 5.958,7.646 4.938,0.25 10 false CAUTION: Terminals H, I, J, K, L, M, N, O, S and T are high-voltage terminals. 2.125,5.781 2.51,6.042 0.385,0.26 10 false C82 4.458,5.781 4.802,5.99 0.344,0.208 10 false C83 3.365,5.781 3.729,6.021 0.365,0.24 10 false C81

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0200 Injector Circuit / Open Open or short in the injector driver or fuel injector circuit (1 trip detection logic).
·

Open or short in injector driver circuit

·

Injector assembly

·

Injector driver

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0200
DTC Detection Drive Pattern Idling for 5 seconds

MONITOR DESCRIPTION

P0200 (Open or short in injector driver or fuel injector circuit):

The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals is inconsistent with the number of INJF signals.

The injector assemblies are grounded through a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (INJF) signal sent from the injector driver to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver, DTC P0200 is stored.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

A145849E18
4.958,2.51 4.625,2.865 false 4.677,3.24 4.885,3.573 false 0.146,0.083 1.729,0.292 1.583,0.208 10 false Malfunction Detection: 2.594,1.365 3,1.563 0.406,0.198 10 false ECM 0.094,1.76 1.781,1.979 1.688,0.219 10 false Injection Command Signal 0.083,3.031 2.042,3.24 1.958,0.208 10 false Injection Confirmation Signal 1.844,2.021 2.448,2.25 0.604,0.229 10 false #1 to #4 2.031,2.781 2.531,3.01 0.5,0.229 10 false INJF 3.302,1.781 3.583,1.979 0.281,0.198 10 false ON 3.552,0.49 5.26,0.781 1.708,0.292 10 false Command Signal (#1 to #4) 3.698,1.094 5.313,1.365 1.615,0.271 10 false Confirmation Signal (INJF) 5.688,1.365 6.573,1.563 0.885,0.198 10 false Injector Driver 3.708,2.146 4.073,2.344 0.365,0.198 10 false OFF 5.031,2.406 5.802,2.604 0.771,0.198 10 false Abnormal 4.979,3.521 5.563,3.719 0.583,0.198 10 false Normal


WIRING DIAGRAM

A205139E57
0.688,0.823 1.063,1.01 0.375,0.188 10 false INJF 1.031,0.813 1.333,0.969 0.302,0.156 10 false C83 1.031,1.25 1.333,1.406 0.302,0.156 10 false C83 1.031,1.688 1.333,1.844 0.302,0.156 10 false C83 1.021,2.125 1.323,2.281 0.302,0.156 10 false C83 1.031,2.563 1.333,2.719 0.302,0.156 10 false C83 1.021,3.052 1.323,3.208 0.302,0.156 10 false C82 1.031,3.979 1.333,4.135 0.302,0.156 10 false C81 1.125,0.615 1.24,0.771 0.115,0.156 10 false 5 0.708,1.26 1,1.427 0.292,0.167 10 false #10 1.125,1.052 1.24,1.208 0.115,0.156 10 false 4 0.698,2.573 0.99,2.74 0.292,0.167 10 false #40 1.125,1.49 1.24,1.646 0.115,0.156 10 false 8 0.719,1.729 1.01,1.896 0.292,0.167 10 false #20 1.125,1.927 1.24,2.083 0.115,0.156 10 false 7 0.719,2.167 1.01,2.333 0.292,0.167 10 false #30 6.198,0.813 6.604,1 0.406,0.188 10 false INJF 6.198,1.219 6.49,1.385 0.292,0.167 10 false #1 6.198,2.552 6.49,2.719 0.292,0.167 10 false #4 6.198,2.104 6.49,2.271 0.292,0.167 10 false #3 6.198,1.667 6.49,1.833 0.292,0.167 10 false #2 5.854,0.813 6.135,0.969 0.281,0.156 10 false C55 5.906,0.615 6.094,0.771 0.188,0.156 10 false 25 5.854,1.25 6.135,1.406 0.281,0.156 10 false C55 5.896,1.052 6.094,1.208 0.198,0.156 10 false 24 5.854,1.688 6.135,1.844 0.281,0.156 10 false C55 5.906,1.49 6.125,1.646 0.219,0.156 10 false 23 5.854,2.125 6.135,2.281 0.281,0.156 10 false C55 5.906,1.927 6.125,2.083 0.219,0.156 10 false 22 5.844,2.563 6.125,2.719 0.281,0.156 10 false C55 5.906,2.375 6.104,2.531 0.198,0.156 10 false 21 1.125,2.375 1.24,2.531 0.115,0.156 10 false 3 0.688,3.094 0.99,3.26 0.302,0.167 10 false IJ1+ 1.125,2.865 1.24,3.021 0.115,0.156 10 false 1 4.26,3.156 4.375,3.313 0.115,0.156 10 false 2 3.594,3.156 3.708,3.313 0.115,0.156 10 false 1 1.125,4.208 1.24,4.365 0.115,0.156 10 false 6 1.104,6.615 1.219,6.771 0.115,0.156 10 false 2 1.125,5.698 1.24,5.854 0.115,0.156 10 false 5 1.125,3.802 1.24,3.958 0.115,0.156 10 false 6 1.125,5.115 1.24,5.271 0.115,0.156 10 false 4 3.438,3.344 4.042,3.531 0.604,0.188 10 false C123 3.438,3.49 4.646,3.719 1.208,0.229 10 false No. 1 Fuel Injector 3.438,4.688 3.771,4.865 0.333,0.177 10 false C19 3.438,7.708 4.646,7.938 1.208,0.229 10 false No. 4 Fuel Injector 3.458,6.188 4.094,6.365 0.635,0.177 10 false C124 3.427,4.844 4.604,5.052 1.177,0.208 10 false No. 2 Fuel Injector 3.438,7.542 3.771,7.719 0.333,0.177 10 false C21 3.438,6.344 4.646,6.583 1.208,0.24 10 false No. 3 Fuel Injector 4.302,4.479 4.417,4.635 0.115,0.156 10 false 2 3.604,4.5 3.719,4.656 0.115,0.156 10 false 1 4.271,5.99 4.385,6.146 0.115,0.156 10 false 2 3.583,5.99 3.698,6.146 0.115,0.156 10 false 1 4.271,7.323 4.385,7.479 0.115,0.156 10 false 2 3.604,7.333 3.719,7.49 0.115,0.156 10 false 1 0.677,3.99 0.948,4.156 0.271,0.167 10 false IJ1- 1.031,4.406 1.333,4.563 0.302,0.156 10 false C82 1.031,5.313 1.333,5.469 0.302,0.156 10 false C81 1.01,5.885 1.313,6.042 0.302,0.156 10 false C82 0.677,4.458 0.979,4.625 0.302,0.167 10 false IJ2+ 0.688,5.354 0.958,5.521 0.271,0.167 10 false IJ2- 0.688,5.927 0.99,6.094 0.302,0.167 10 false IJ3+ 0.688,6.792 0.958,6.958 0.271,0.167 10 false IJ3- 1.031,7.229 1.333,7.385 0.302,0.156 10 false C81 1.031,8.146 1.333,8.302 0.302,0.156 10 false C81 1.031,6.802 1.333,6.958 0.302,0.156 10 false C81 1.125,7.042 1.25,7.198 0.125,0.156 10 false 3 1.094,7.969 1.208,8.125 0.115,0.156 10 false 5 0.656,7.24 0.958,7.406 0.302,0.167 10 false IJ4+ 0.667,8.135 0.938,8.302 0.271,0.167 10 false IJ4- 6.375,8.438 6.708,8.604 0.333,0.167 10 false ECM 0.208,8.469 1.458,8.708 1.25,0.24 10 false Injector Driver

A355776E01
0.031,5.125 0.938,5.323 0.906,0.198 10 false Injector Driver 6.594,5.125 7.052,5.323 0.458,0.198 10 false ECM 0.51,0.406 0.969,0.604 0.458,0.198 10 false +B 0.396,0.865 0.854,1.063 0.458,0.198 10 false GND 0.813,0.406 1.271,0.604 0.458,0.198 10 false C82 0.813,0.854 1.271,1.052 0.458,0.198 10 false C82 3.021,0.521 3.198,0.719 0.177,0.198 10 false 5 3.781,0.521 3.958,0.719 0.177,0.198 10 false 2 3.781,1.302 3.958,1.5 0.177,0.198 10 false 1 3.021,1.292 3.198,1.49 0.177,0.198 10 false 3 4,0.906 4.458,1.104 0.458,0.198 10 false EDU 2.156,1.698 2.615,1.896 0.458,0.198 10 false EDU 1.552,4.344 2.135,4.74 0.583,0.396 10 false FL MAIN 3.0W 1.76,4 2.219,4.198 0.458,0.198 10 false J/B-B 2.469,4.385 4.104,4.76 1.635,0.375 10 false Instrument Panel Junction Block 2.5,3.833 2.74,4.052 0.24,0.219 10 false 2B 3.625,2.104 3.865,2.323 0.24,0.219 10 false 2K 5.208,2.385 5.448,2.604 0.24,0.219 10 false 2G 5.219,2.802 5.458,3.021 0.24,0.219 10 false 2P 2.865,3.969 3.917,4.156 1.052,0.188 10 false EFI-MAIN NO. 1 4.531,3.219 5.208,3.615 0.677,0.396 10 false EFI-MAIN NO. 1 4.198,4.156 4.438,4.375 0.24,0.219 10 false 2J 6.156,2.802 6.479,3.021 0.323,0.219 10 false G84 6.156,2.375 6.479,2.594 0.323,0.219 10 false G84 6.156,0.406 6.479,0.625 0.323,0.219 10 false G84 3.604,2.281 3.781,2.479 0.177,0.198 10 false 4 4.146,3.979 4.323,4.177 0.177,0.198 10 false 5 5.26,2.188 5.438,2.385 0.177,0.198 10 false 5 5.26,2.635 5.438,2.833 0.177,0.198 10 false 9 6.198,0.219 6.448,0.417 0.25,0.198 10 false 10 6.229,2.615 6.406,2.813 0.177,0.198 10 false 8 6.208,2.177 6.385,2.375 0.177,0.198 10 false 1 0.885,0.219 1.063,0.417 0.177,0.198 10 false 2 0.885,0.677 1.063,0.875 0.177,0.198 10 false 3 2.531,3.646 2.708,3.844 0.177,0.198 10 false 1 6.5,0.406 6.958,0.604 0.458,0.198 10 false IREL 6.51,2.385 6.969,2.583 0.458,0.198 10 false +B 6.51,2.802 6.969,3 0.458,0.198 10 false MREL 1.667,5.125 2.573,5.323 0.906,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:
·

When DTC P0200 is stored, the malfunctioning parts can be narrowed down according to fail-safe behavior.

·

When a DTC is stored but the engine does not stall, there may be an open circuit or malfunction in the following components which affect the control of individual cylinders.

1.

The circuit inside an injector assembly.

2.

The wiring between an injector driver and injector assembly (between terminal IJ1+ and the No. 1 injector assembly, terminal IJ1 and the No. 1 injector assembly, etc.).

3.

The wiring between an injector driver and the ECM (terminals #10 and #1, etc.).


·

When a DTC is stored and the engine stalls, there may be a malfunction in the wiring which affects the control of multiple cylinders.

1.

Wiring between an injector driver and the ECM (between INJF terminals).

2.

The power supply wiring.



·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Engine does not start*1 A
Engine starts, but idling is rough*2 B
Except above C


HINT:
·

*1: Once DTC P0200 is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).

When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Common Rail Pressure" is higher than the value for "Target Common Rail Pressure"

·

*2: DTC P0200 is stored at this time.





A

2.CHECK ECM

B

7.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 to #4)

C

2.CHECK ECM
a.
A303051C15
0.531,0.292 0.906,0.563 0.375,0.271 1.188,0.292 1.563,0.563 0.375,0.271 0.323,1.906 0.625,1.052 true 0.594,1.74 0.677,1.052 true 1.188,1.906 0.74,1.063 true 1.281,1.74 0.792,1.063 true 1.99,1.74 1.125,0.896 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.604,0.354 1.052,0.583 0.448,0.229 10 false C55 1.26,0.354 1.625,0.594 0.365,0.24 10 false C56 0.208,1.958 0.708,2.177 0.5,0.219 10 false 24 (#1) 0.49,1.75 0.958,1.979 0.469,0.229 10 false 23 (#2) 1.094,1.948 1.823,2.167 0.729,0.219 10 false 22 (#3) 1.25,1.75 1.74,1.979 0.49,0.229 10 false 21 (#4) 2,1.75 2.438,1.969 0.438,0.219 10 false 7 (E1) 2.448,2.208 3.104,2.406 0.656,0.198 10 false 2 V/DIV. 3.021,3.365 3.396,3.563 0.375,0.198 10 false GND 0.385,4.208 1.448,4.406 1.063,0.198 10 false 1 msec./DIV.
*a Component with harness connected
(ECM)


Check the waveform of the ECM connectors using an oscilloscope.


b.

Check the waveform of the injector driver (EDU) connectors using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C55-24 (#1) - C56-7 (E1) Cranking Correct waveform is as shown
C55-23 (#2) - C56-7 (E1) Cranking Correct waveform is as shown
C55-22 (#3) - C56-7 (E1) Cranking Correct waveform is as shown
C55-21 (#4) - C56-7 (E1) Cranking Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE

NG

6.REPLACE ECM
3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE
a.
A221614C61
0.51,1.396 0.896,1.656 0.385,0.26 1.688,1.156 1.167,0.813 true 2.438,1.656 1.979,1.271 true 0.573,1.448 0.896,1.656 0.323,0.208 10 false C82 0.75,0.76 1.24,1.042 0.49,0.281 10 false +B (+) 0.125,0.24 0.323,0.396 0.198,0.156 10 false *a 2.51,1.615 3.083,1.896 0.573,0.281 10 false GND (-)
*a Front view of wire harness connector
(to Injector Driver)


Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C82-2 (+B) - C82-3 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connectors.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-4 (#10) - C55-24 (#1) Always Below 1 Ω
C83-8 (#20) - C55-23 (#2) Always Below 1 Ω
C83-7 (#30) - C55-22 (#3) Always Below 1 Ω
C83-3 (#40) - C55-21 (#4) Always Below 1 Ω
C83-5 (INJF) - C55-25 (INJF) Always Below 1 Ω
C83-4 (#10) or C55-24 (#1) - Body ground Always 10 kΩ or higher
C83-8 (#20) or C55-23 (#2) - Body ground Always 10 kΩ or higher
C83-7 (#30) or C55-22 (#3) - Body ground Always 10 kΩ or higher
C83-3 (#40) or C55-21 (#4) - Body ground Always 10 kΩ or higher
C83-5 (INJF) or C55-25 (INJF) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE INJECTOR DRIVER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 to #4)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 234 778,779,780,781

d.

Start the engine.


e.

Read the Injection Feedback Val #1 to #4 values while idling the engine.

Standard Value:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #4 Idling +3.0 mm3/st or less


HINT:
·

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.

·

Fuel is not being injected in cylinders whose "Injection Feedback Val" is higher than 3 mm3/st. Inspection procedures beyond this point diagnose whether there are internal problems with fuel injectors, or whether there is a problem in the wiring of the fuel injector system.




Result:
Proceed to
NEXT



NEXT

8.INSPECT INJECTOR ASSEMBLY (RESISTANCE)
8.INSPECT INJECTOR ASSEMBLY (RESISTANCE)
a.
A191333C03
1.885,1.083 2,1.229 0.115,0.146 10 false 2 1.479,1.083 1.594,1.229 0.115,0.146 10 false 1 0.177,0.281 0.427,0.542 0.25,0.26 10 false *a
*a Component without harness connected
(Fuel Injector)


Disconnect the fuel injector connectors.


b.

Measure the resistance of the fuel injector

OK:

No open or short circuit malfunction.



c.

Reconnect the fuel injector connectors.


Result:
Proceed to
OK
NG



OK

9.INSPECT INJECTOR DRIVER

NG

10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
9.INSPECT INJECTOR DRIVER
a.
A303105C21
0.396,0.792 0.781,1.052 0.385,0.26 0.844,1.125 1.229,1.385 0.385,0.26 0.406,1.135 0.781,1.385 0.375,0.25 0.844,0.792 1.229,1.063 0.385,0.271 0.438,0.844 0.823,1.042 0.385,0.198 10 false C123 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.219,2.24 2.927,2.469 0.708,0.229 10 false 10 V/DIV. 0.313,4.271 1.271,4.479 0.958,0.208 10 false 1 msec./DIV. 3,4.031 3.385,4.25 0.385,0.219 10 false GND 0.875,0.844 1.271,1.031 0.396,0.188 10 false C124 0.479,1.177 0.781,1.365 0.302,0.188 10 false C19 0.906,1.177 1.208,1.365 0.302,0.188 10 false C21
*a Front view of wire harness connector
(to Fuel Injector)


Disconnect the fuel injector connectors for all cylinders.


b.

Check the waveform of the fuel injector connectors using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C123-1 - C123-2 Cranking Voltage increases by 50 V or more
C19-1 - C19-2 Cranking Voltage increases by 50 V or more
C124-1 - C124-2 Cranking Voltage increases by 50 V or more
C21-1 - C21-2 Cranking Voltage increases by 50 V or more



Result:
Proceed to
OK
NG



OK

10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

13.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
a.

Disconnect the injector assembly connectors.


b.

Disconnect the injector driver connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C123-1 - C82-1 (IJ1+) Always Below 1 Ω
C123-2 - C81-6 (IJ1-) Always Below 1 Ω
C19-1 - C82-6 (IJ2+) Always Below 1 Ω
C19-2 - C81-4 (IJ2-) Always Below 1 Ω
C124-1 - C82-5 (IJ3+) Always Below 1 Ω
C124-2 - C81-2 (IJ3-) Always Below 1 Ω
C21-1 - C81-3 (IJ4+) Always Below 1 Ω
C21-2 - C81-5 (IJ4-) Always Below 1 Ω
C123-1 or C82-1 (IJ1+) - Body ground Always 10 kΩ or higher
C123-2 or C81-6 (IJ1-) - Body ground Always 10 kΩ or higher
C19-1 or C82-6 (IJ2+) - Body ground Always 10 kΩ or higher
C19-2 or C81-4 (IJ2-) - Body ground Always 10 kΩ or higher
C124-1 or C82-5 (IJ3+) - Body ground Always 10 kΩ or higher
C124-2 or C81-2 (IJ3-) - Body ground Always 10 kΩ or higher
C21-1 or C81-3 (IJ4+) - Body ground Always 10 kΩ or higher
C21-2 or C81-5 (IJ4-) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector assembly connectors.


e.

Reconnect the injector driver connectors.


Result:
Proceed to
OK
NG



OK

14.REPLACE INJECTOR DRIVER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE INJECTOR DRIVER
a.

Replace the injector driver.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END