Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P1251  Step Motor for Turbocharger Control Circuit (Intermittent)  


DESCRIPTION

HINT:

Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0046).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1251 Turbocharger / Supercharger Overboost Condition (Too High) Boost pressure is higher than the threshold* for 0.5 seconds. (1 trip detection logic).
·

Turbocharger sub-assembly

·

VN turbo link stuck malfunction

·

Extremely low battery voltage (P0560 stored simultaneously)

·

Intake system

·

Exhaust system

·

Injector assembly

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored

HINT:

*: This value changes based on engine speed, atmospheric pressure and the engine coolant temperature (the value is generally between 177 and 250 kPa).


Related Data List
DTC No. Data List
P1251
·

MAP

·

Target Booster Pressure

·

MAF

·

VN Turbo Command

·

Actual VN Position

·

Atmosphere Pressure



HINT:

If DTC P1251 is stored due to the VN turbo vane being stuck closed, the following symptoms may appear:

·

Vehicle surge when driving with full load

·

Sudden lack of power due to power being limited



CONFIRMATION DRIVING PATTERN

P1251
DTC Detection Drive Pattern Vehicle being driven

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

HINT:
·

Record the stored DTC and Freeze Frame Data.

·

Be sure to carefully examine "MAP" and "Target Booster Pressure" in the freeze frame data.



Result:
Result Proceed to
P1251 is output A
P1251 and other DTCs are output B


HINT:

DC motor-related DTCs: P0046 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0046), P0047 and P0048 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0047).

Nozzle vane position sensor-related DTCs: P2563, P2564, P2565, P2588 and P2589 (See pageEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P2563).




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check if the hoses between the air cleaner and turbocharger, and turbocharger and intake manifold are damaged or disconnected.

Result:
Result Proceed to
Hoses or pipes are damaged or disconnected A
No hoses or pipes are damaged or disconnected B


HINT:
·

Be sure to check if the hoses and pipes between the air cleaner and compressor are disconnected as disconnection of a hose or pipe can cause overboost. Also, check the high pressure hoses for disconnection due to overboost.

·

Check for disconnection of the exhaust pipes.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
3.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
4.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
a.

Turn the ignition switch to ON.


b.

Turn the ignition switch off and check the DC motor operation (check the operation link movement).

HINT:

When it is necessary to repeat this inspection, wait 30 seconds or more with the ignition switch off before performing the inspection.


OK:

When ignition switch is turned off, operation link moves as shown in A through D in illustration below.

Operation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.


A158317E08
5.635,1.208 6.021,1.146 false 5.542,1.615 5.906,1.51 false 5.458,1.969 6,1.927 false 4.74,4.125 5.698,3.583 false 1.938,0.24 2.094,0.438 0.156,0.198 10 false A 3.063,0.229 3.219,0.427 0.156,0.198 10 false B 4.51,0.229 4.667,0.427 0.156,0.198 10 false C 5.385,0.229 5.542,0.427 0.156,0.198 10 false D 0.333,1.958 1.469,2.354 1.135,0.396 10 false Motor Rod Stroke (mm (in.)) 2.5,4.406 4.583,4.74 2.083,0.333 10 false Ignition Switch off Time (sec.) 5.948,1.427 6.677,1.677 0.729,0.25 10 false Lock Nut 6.063,1.073 7.031,1.333 0.969,0.26 10 false Operation Link 6.042,1.844 7.021,2.125 0.979,0.281 10 false Stopper Bolt 5.75,3.49 7.125,3.781 1.375,0.292 10 false Stopper Bolt Contact 1.24,4.719 1.563,4.99 0.323,0.271 10 false ON 1.583,5.063 1.823,5.302 0.24,0.24 10 false off 0.125,4.885 1.104,5.156 0.979,0.271 10 false Ignition Switch


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (INJECTION VOLUME)

NG

10.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - TURBOCHARGER SUB-ASSEMBLY)
5.READ VALUE USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Allow the engine to idle for 1 minute or more.

HINT:

The A/C switch and all accessory switches should be off with a fully warm engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Injection Volume.

Powertrain > Engine > Data List
Tester Display
Injection Volume
50003 234 786

f.

Read the values during engine idling.

Result:
Result Proceed to
Injection Volume is less than 4 mm3/st A
Except above B


HINT:
·

If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector to inject.





A

6.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.BLEED AIR FROM FUEL SYSTEM
7.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

8.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
8.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Start the engine.


e.

Drive the vehicle with a city driving pattern at least 10 minutes.


f.

Confirm the value of Engine Speed from the Freeze Frame Data recorded previously, and then drive the vehicle according to the Engine Speed value.

HINT:

Take a snapshot of MAP and Target Boost Pressure in the Data List with the GTS while driving the vehicle.



g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
P1251 is not output and the amount by which MAP exceeds Target Boost Pressure is 20 kPa or less A
Except above B
*


HINT:

*: Return to "Check Air Intake System" and inspect areas that have not been inspected yet.




A

END

B

2.CHECK AIR INTAKE SYSTEM
10.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - TURBOCHARGER SUB-ASSEMBLY)
a.

Disconnect the DC motor connector.


b.

Disconnect the nozzle vane position sensor connector.


c.

Disconnect the turbo motor driver connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C91-2 (M+) - C90-12 (M+) Always Below 1 Ω
C91-1 (M-) - C90-5 (M-) Always Below 1 Ω
C92-1 (VTA1) - C90-9 (VTA1) Always Below 1 Ω
C92-2 (VNE2) - C90-8 (VNE2) Always Below 1 Ω
C92-3 (VNVC) - C90-1 (VNVC) Always Below 1 Ω
C92-4 (VTA2) - C90-10 (VTA2) Always Below 1 Ω
C92-5 (E2S) - C90-11 (E2S) Always Below 1 Ω
C92-6 (VCS) - C90-6 (VCS) Always Below 1 Ω
C91-2 (M+) or C90-12 (M+) - Body ground Always 10 kΩ or higher
C91-1 (M-) or C90-5 (M-) - Body ground Always 10 kΩ or higher
C92-1 (VTA1) or C90-9 (VTA1) - Body ground Always 10 kΩ or higher
C92-2 (VNE2) or C90-8 (VNE2) - Body ground Always 10 kΩ or higher
C92-3 (VNVC) or C90-1 (VNVC) - Body ground Always 10 kΩ or higher
C92-4 (VTA2) or C90-10 (VTA2) - Body ground Always 10 kΩ or higher
C92-5 (E2S) or C90-11 (E2S) - Body ground Always 10 kΩ or higher
C92-6 (VCS) or C90-6 (VCS) - Body ground Always 10 kΩ or higher



e.

Reconnect the DC motor connector.


f.

Reconnect the nozzle vane position sensor connector.


g.

Reconnect the turbo motor driver connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR