Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _038013 2KD-FTV ENGINE CONTROL _0184270 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A208462E18
1.49,2 1.646,1.76 1.646,1.76 1.792,1.76 false 0.208,0.146 0.75,0.385 0.542,0.24 10 false (Fig. 1) 0.208,0.542 1.229,0.781 1.021,0.24 10 false Resistance kΩ 1.823,1.667 2.604,1.875 0.781,0.208 10 false Acceptable 1.208,4.063 2.521,4.281 1.313,0.219 10 false Temperature °C (°F)

The Intake Air Temperature (IAT) sensor, mounted on the air cleaner hose, monitors the IAT. The IAT sensor has a thermistor that varies its resistance depending on the temperature of the intake air. When the air temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance decreases. The variations in resistance are communicated to the ECM as changes in voltage (see Fig. 1).

The IAT sensor is connected to the ECM (see below). The 5 V power source voltage in the ECM is applied to the IAT sensor from terminal THA via resistor R.

The resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes in accordance with changes in the IAT, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve the driveability during cold engine operation.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0110 Intake Air Temperature Circuit Open or short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in IAT sensor circuit

·

IAT sensor

·

ECM


- DTC stored
P0112 Intake Air Temperature Circuit Low Input Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in IAT sensor circuit

·

IAT sensor

·

ECM


- DTC stored
P0113 Intake Air Temperature Circuit High Input Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in IAT sensor circuit

·

IAT sensor

·

ECM


- DTC stored

HINT:

When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


CONFIRMATION DRIVING PATTERN

P0110, P0112, P0113
DTC Detection Drive Pattern Ignition switch to ON for 0.5 seconds

WIRING DIAGRAM

A255058E61
0.313,2.104 2.344,2.344 2.031,0.24 10 false Intake Air Temperature Sensor 0.313,1.938 0.646,2.146 0.333,0.208 10 false A54 5.948,2.458 6.344,2.667 0.396,0.208 10 false ECM 5.438,0.979 5.802,1.177 0.365,0.198 10 false THA 5.458,1.563 5.688,1.75 0.229,0.188 10 false E2 5.896,0.219 6.208,0.438 0.313,0.219 10 false 5 V 6.104,0.656 6.333,0.885 0.229,0.229 10 false R 1.969,0.979 2.146,1.188 0.177,0.208 10 false 2 1.969,1.552 2.146,1.771 0.177,0.219 10 false 1 5.948,2.313 6.292,2.51 0.344,0.198 10 false C55 5.208,0.979 5.417,1.177 0.208,0.198 10 false 31 5.219,1.563 5.417,1.76 0.198,0.198 10 false 28 1.573,1.01 2.031,1.208 0.458,0.198 10 false THA 1.615,1.583 1.927,1.781 0.313,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 234 5

d.

Read the value.

OK:

Same as actual intake air temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A303339C03
0.469,3.521 0.896,3.792 0.427,0.271 1.198,4.104 1.469,3.74 false 2.219,4.094 1.958,3.729 false 0.323,0.438 0.635,0.635 0.313,0.198 10 false *1 2.76,0.354 3.073,0.552 0.313,0.198 10 false *2 2.448,1.156 2.854,1.354 0.406,0.198 10 false THA 2.458,1.521 2.771,1.719 0.313,0.198 10 false E2 0.396,2.625 0.708,2.823 0.313,0.198 10 false *a 1.073,4.167 1.385,4.365 0.313,0.198 10 false E2 2.146,4.156 2.604,4.354 0.458,0.198 10 false THA 0.563,3.583 0.958,3.844 0.396,0.26 10 false A54
*1 Intake Air Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor)


Disconnect the A54 intake air temperature sensor connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON and turn the GTS ON.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 234 5

f.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


g.

Read the values.

OK:

140°C (284°F) or more



h.

Reconnect the intake air temperature sensor connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor (w/o mass air flow meter).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A54-2(THA) - A55-31 (THA) Always Below 1 Ω
A54-1(E2) - A55-28 (E2) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C02
2.396,1.031 2.729,1.229 0.333,0.198 10 false THA 2.438,1.5 2.729,1.76 0.292,0.26 10 false E2 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Intake Air Temperature Sensor
*2 ECM


Disconnect the intake air temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 234 5

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the intake air temperature sensor connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
7.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standerd resistance:
Tester Connection Condition Specified Condition
A54-1 or C55-31 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED