Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _038013 2KD-FTV ENGINE CONTROL _0184270 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal.

A128639E42
2.521,2.073 2.854,3.073 false 2.417,2.615 2.219,3.104 false 2.188,0.802 2.417,1.26 false 1.698,0.229 3.25,0.438 1.552,0.208 10 false Throttle Position Sensor 2.896,3.01 3.438,3.208 0.542,0.198 10 false Hall IC 4.375,0.635 4.781,0.844 0.406,0.208 10 false ECM 4.385,1.073 4.677,1.271 0.292,0.198 10 false 5 V 3.635,1.167 4.073,1.365 0.438,0.198 10 false VC 3.573,1.792 4.031,1.99 0.458,0.198 10 false VLU 3.656,2.396 4.052,2.594 0.396,0.198 10 false E2 3.146,1.177 3.406,1.375 0.26,0.198 10 false VC 3.146,2.406 3.385,2.604 0.24,0.198 10 false E2 3.146,1.792 3.51,1.99 0.365,0.198 10 false VTA 1.688,3.031 2.281,3.24 0.594,0.208 10 false Magnet 1.688,0.667 2.281,0.875 0.594,0.208 10 false Magnet

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM


Comes on DTC stored

HINT:

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


CONFIRMATION DRIVING PATTERN

P0122, P0123
DTC Detection Drive Pattern Ignition switch to ON for 3 seconds

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

A301850E05
2,1.271 2.292,1.094 false 3.427,1 3.698,0.333 false 3.708,0.333 3.781,0.333 false 4.594,3.104 4.396,2.688 false 4.604,3.104 4.677,3.104 false 2.094,2.792 2.292,2.656 false 3.823,0.26 4.708,0.469 0.885,0.208 10 false Stores P0123 0.052,1.448 1.563,1.948 1.51,0.5 10 false Throttle Position Sensor Output Voltage (V) 2.563,3.396 4.365,3.646 1.802,0.25 10 false Throttle Valve Opening Angle 4.708,3.021 5.646,3.25 0.938,0.229 10 false Stores P0122 3.969,0.667 4.354,0.885 0.385,0.219 10 false Open 1.844,0.729 2.375,0.979 0.531,0.25 10 false Closed 2.594,2.74 3.802,2.979 1.208,0.24 10 false Range of Operation 2,0.938 2.344,1.146 0.344,0.208 10 false 5.00 1.688,1.219 2.01,1.417 0.323,0.198 10 false 4.80 1.99,1.396 2.344,1.625 0.354,0.229 10 false 3.49 1.969,2.396 2.375,2.625 0.406,0.229 10 false 0.69 2.271,3.198 2.427,3.396 0.156,0.198 10 false 0 4.083,3.188 4.385,3.427 0.302,0.24 10 false 70° 1.802,2.76 2.135,2.948 0.333,0.188 10 false 0.20

WIRING DIAGRAM

A154311E29
0.625,3.219 0.958,3.406 0.333,0.188 10 false C76 0.625,3.406 2.167,3.563 1.542,0.156 10 false Throttle Position Sensor 2.177,1.552 2.313,1.708 0.135,0.156 10 false 1 2.177,2.031 2.417,2.188 0.24,0.156 10 false 3 2.177,2.5 2.417,2.656 0.24,0.156 10 false 2 5.156,1.458 5.365,1.635 0.208,0.177 10 false 18 5.125,1.635 5.438,1.813 0.313,0.177 10 false C55 5.125,2.115 5.552,2.542 0.427,0.427 10 false C56 5.125,2.573 5.417,2.75 0.292,0.177 10 false C55 5.448,1.552 5.719,1.729 0.271,0.177 10 false VC 5.156,1.948 5.365,2.125 0.208,0.177 10 false 29 5.448,2.042 5.771,2.219 0.323,0.177 10 false VLU 5.156,2.396 5.365,2.573 0.208,0.177 10 false 28 5.448,2.49 5.771,2.667 0.323,0.177 10 false E2 1.854,1.625 2.094,1.802 0.24,0.177 10 false VC 1.792,2.115 2.115,2.292 0.323,0.177 10 false VTA 1.875,2.563 2.125,2.74 0.25,0.177 10 false E2 6.24,2.792 6.563,2.969 0.323,0.177 10 false E1 5.99,1.115 6.313,1.292 0.323,0.177 10 false 5 V 5.885,3.25 6.281,3.427 0.396,0.177 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C76-1 (VC) - C55-18 (VC) Always Below 1 Ω
C76-3 (VTA) - C56-29 (VLU) Always Below 1 Ω
C76-2 (E2) - C55-28 (E2) Always Below 1 Ω
C76-1 (VC) or C55-18 (VC) - Body ground Always 10 kΩ or higher
C76-3 (VTA) or C56-29 (VLU) - Body ground Always 10 kΩ or higher
C76-2 (E2) or C55-28 (E2) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
C129053C26
0.76,1.125 1.073,1.354 0.313,0.229 1.26,1.583 1.458,1.26 true 1.76,1.25 1.99,1.594 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.792,1.156 1.104,1.333 0.313,0.177 10 false C76 1.094,1.625 1.406,1.823 0.313,0.198 10 false VC 2.01,1.615 2.271,1.813 0.26,0.198 10 false E2
*a Front view of wire harness connector
(to Throttle Position Sensor)


Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C76-1 (VC) - C76-2 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS
4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Enter the following menus: Powertrain / Engine / Data List / Actual Throttle position.

Powertrain > Engine > Data List
Tester Display
Actual Throttle Position
50003 234 830

e.

Check the movement of the throttle valve when idling the engine after starting it from ignition switch to ON.

OK:
Condition GTS Display
Ignition switch ON -5 to 5%
Idling 0 to 90%



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END