Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _038013 2KD-FTV ENGINE CONTROL _0184270 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0168  Fuel Temperature Too High  


DESCRIPTION

Refer to DTC P0180 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>P0180).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0168 Fuel Temperature Too High Both of following conditions are met (1 trip detection logic):
·

The engine speed is more than 3200 rpm.

·

The fuel temperature is 96°C (205°F) or higher for the specified time.


·

Fuel cooler (Problem cooling fuel)

·

Fuel lines or fuel filter clogged


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0168
DTC Detection Drive Pattern Drive vehicle at high speed or with heavy load (Use freeze frame data from time malfunction occurred as reference while driving)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0168)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
P0168 is output A
P0168 and other DTCs are output B


HINT:

If DTCs other than P0168 are output, perform troubleshooting for those codes first.




A

2.CHECK FUEL SUPPLY PUMP ASSEMBLY

B

2.CHECK FUEL SUPPLY PUMP ASSEMBLY
a.

Perform a visual inspection of the exterior of the fuel supply pump assembly and check that there are no fuel leaks.

OK:

There are no fuel leaks or stains.



Result:
Proceed to
OK
NG



OK

3.CHECK FUEL SYSTEM

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
3.CHECK FUEL SYSTEM
a.

Check if dirt is clogging the fuel cooler cooling fins. Clean the fins if they are clogged with dirt.

HINT:

If the fuel cooler cooling fins are not clogged with dirt, replace the fuel filter element assembly.



Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch to ON and turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 234 852

f.

Drive the vehicle in a city area and check that the value of Fuel Temperature does not exceed 110°C (230°F).


Result:
Proceed to
NEXT



NEXT

END