Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP
RM3250E _59 Vehicle Exterior _038080 EXTERIOR PANELS / TRIM _0184365 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 51774C 1.REMOVE STEP PLATE COVER LH

a.

for Single Cab:

i.

Remove the 2 bolts.

B409568


ii.

Detach the claw and guide and remove the step plate cover LH.

NOTICE:
·

When removing the step plate cover LH, be careful not to damage the claws.

·

If the step plate cover LH or its claws are damaged, replace it with a new one.





b.

for Smart Cab:

i.

Remove the 2 bolts.

B399493


ii.

Detach the claw and guide and remove the step plate cover LH.

NOTICE:
·

When removing the step plate cover LH, be careful not to damage the claws.

·

If the step plate cover LH or its claws are damaged, replace it with a new one.





c.

for Double Cab:

i.

Remove the 2 bolts.

B399502


ii.

Detach the claw and guide and remove the step plate cover LH.

NOTICE:
·

When removing the step plate cover LH, be careful not to damage the claws.

·

If the step plate cover LH or its claws are damaged, replace it with a new one.





Hide 51082 2.REMOVE NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH

a.

for Single Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B409569N02
0.583,0.948 0.74,1.146 0.156,0.198 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 1 side step stay sub-assembly LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



b.

for Smart Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B399496N01
0.49,0.958 0.688,1.198 0.198,0.24 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 1 side step stay sub-assembly LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



c.

for Double Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B399504N01
0.438,0.958 0.635,1.198 0.198,0.24 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 1 side step stay sub-assembly LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



Hide 51796 3.REMOVE NO. 2 SIDE STEP BRACKET LH

a.

for Single Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B409570N03
0.594,0.958 0.75,1.156 0.156,0.198 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 2 side step bracket LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



b.

for Smart Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B399497N01
0.427,0.958 0.625,1.208 0.198,0.25 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 2 side step bracket LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



c.

for Double Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B403614N01
0.406,0.979 0.698,1.25 0.292,0.271 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 2 side step bracket LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



Hide 51798 4.REMOVE NO. 3 SIDE STEP BRACKET LH

a.

for Smart Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B399498N01
0.385,0.896 0.625,1.135 0.24,0.24 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 3 side step bracket LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.



b.

for Double Cab:

i.

Put a 5 mm (0.197 in.) drill bit into a drill.

B403615N01
0.448,0.938 0.656,1.188 0.208,0.25 10 false A

Standard:
Area Specified Condition
A 5 mm (0.197 in.)



ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 5 mm (0.197 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




iv.

Remove the No. 3 side step bracket LH from the step plate LH.


v.

Using a vacuum cleaner, remove the 2 rivets fragments and shavings from the drilled area.