Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM3250E _59 Vehicle Exterior _038080 EXTERIOR PANELS / TRIM _0184369 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:
·

It is only necessary to perform this procedure when replacing a roof drip side finish moulding clip with a new one.

·

If installing new roof drip side finish moulding clips, remove the adhesive remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.



HINT:

When installing the roof drip side finish moulding clip, heat the vehicle body and roof drip side finish moulding clip using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding Clip 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B187426C10
2.073,0.781 2.385,0.781 false 0.99,1.052 1.229,1.052 1.229,1.052 1.344,1.51 true 1.823,0.667 2.052,0.854 0.229,0.188 10 false *1 0.74,0.938 1.031,1.135 0.292,0.198 10 false *a
*1 Adhesive
*a 2.0 to 3.0 mm Bead of Adhesive


Apply a 2.0 to 3.0 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1991 psi) or more (when the temperature is 23°C (73°F))



b.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.

Single Cab:

i.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the roof drip side finish moulding clip after lightly pressing it so that the adhesive adheres to the primer.

B399462C01
2.781,0.635 3.031,0.635 false 6.552,2.854 6.823,2.854 false 0.958,1.156 1.115,1.354 0.156,0.198 10 false A 2.688,0.188 2.844,0.385 0.156,0.198 10 false B 4.229,3.26 4.385,3.458 0.156,0.198 10 false C 4.656,3.26 4.813,3.458 0.156,0.198 10 false D 6.458,2.406 6.615,2.604 0.156,0.198 10 false E 3.104,0.542 3.417,0.74 0.313,0.198 10 false *a 6.865,2.771 7.125,2.99 0.26,0.219 10 false *a
*a Edge of Curved Surface - -


Standard:
Area Specified Condition Area Specified Condition
A 4.0 mm (0.157 in.) B 2.6 mm (0.102 in.)
C 4.0 mm (0.157 in.) D 4.0 mm (0.157 in.)
E 2.0 mm (0.0787 in.) - -


NOTICE:

Install the roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours





d.

Smart Cab:

i.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the roof drip side finish moulding clip after lightly pressing it so that the adhesive adheres to the primer.

B399463C02
2.792,0.656 3.104,0.656 false 6.563,2.823 6.865,2.823 false 0.969,1.146 1.125,1.344 0.156,0.198 10 false A 2.677,0.188 2.833,0.385 0.156,0.198 10 false B 4.229,3.25 4.385,3.448 0.156,0.198 10 false C 4.646,3.25 4.802,3.448 0.156,0.198 10 false D 6.458,2.417 6.615,2.615 0.156,0.198 10 false E 3.125,0.573 3.438,0.771 0.313,0.198 10 false *a 6.885,2.74 7.156,2.979 0.271,0.24 10 false *a
*a Edge of Curved Surface - -


Standard:
Area Specified Condition Area Specified Condition
A 4.0 mm (0.157 in.) B 2.6 mm (0.102 in.)
C 4.0 mm (0.157 in.) D 4.0 mm (0.157 in.)
E 2.0 mm (0.0787 in.) - -


NOTICE:

Install the roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours





e.

Double Cab:

i.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the roof drip side finish moulding clip after lightly pressing it so that the adhesive adheres to the primer.

B399464C02
2.781,0.667 3.094,0.667 false 6.563,2.854 6.875,2.854 false 0.969,1.135 1.125,1.333 0.156,0.198 10 false A 2.677,0.188 2.833,0.385 0.156,0.198 10 false B 4.229,3.271 4.385,3.469 0.156,0.198 10 false C 4.656,3.26 4.813,3.458 0.156,0.198 10 false D 6.458,2.438 6.615,2.635 0.156,0.198 10 false E 3.135,0.573 3.448,0.771 0.313,0.198 10 false *a 6.917,2.76 7.156,2.958 0.24,0.198 10 false *a
*a Edge of Curved Surface - -


Standard:
Area Specified Condition Area Specified Condition
A 4.0 mm (0.157 in.) B 2.6 mm (0.102 in.)
D 4.0 mm (0.157 in.) C 4.0 mm (0.157 in.)
E 2.0 mm (0.0787 in.) - -


NOTICE:

Install the roof drip side finish moulding LH when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours





Hide 75552 2.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

HINT:

When installing the roof drip side finish moulding LH, heat the vehicle body and roof drip side finish moulding LH using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new roof drip side finish moulding LH.

i.

Using a heat light, heat the vehicle body and a new roof drip side finish moulding LH.


ii.

Remove the peeling paper from the face of the roof drip side finish moulding LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B405728

for Single Cab:

1.

Attach the clip to install the roof drip side finish moulding LH.


HINT:

Press the roof drip side finish moulding LH firmly to install it.



iv.
B405729

for Smart Cab:

1.

Attach the clip to install the roof drip side finish moulding LH.


HINT:

Press the roof drip side finish moulding LH firmly to install it.



v.
B405730

for Double Cab:

1.

Attach the clip to install the roof drip side finish moulding LH.


HINT:

Press the roof drip side finish moulding LH firmly to install it.




c.

Remove the protective tape.