Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM3250E _59 Vehicle Exterior _038075 WINDOW / GLASS _0184380 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Entry and Start System)


*1: for LHD

*2: for RHD


a.
B187998C05
0.792,0.177 1.177,0.49 0.385,0.313 1.75,0.156 2.135,0.469 0.385,0.313 0.875,0.229 1.188,0.427 0.313,0.198 10 false K6 1.271,0.24 1.583,0.438 0.313,0.198 10 false *A 1.833,0.219 2.146,0.417 0.313,0.198 10 false J12 2.219,0.229 2.531,0.427 0.313,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the K6*1 or J12*2 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K6-11 (B) - K6-12 (GND) Y - W-B Power supply Always 11 to 14 V
K6-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J12-11 (B) - J12-12 (GND) Y - W-B Power supply Always 11 to 14 V
J12-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K6*1 or J12*2 power window regulator master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K6-15 (DOWN) - K6-12 (GND) P - W-B Driver door power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
K6-20 (UP) - K6-12 (GND) B - W-B Driver door power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J12-15 (DOWN) - J12-12 (GND) P - W-B Driver door power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J12-20 (UP) - J12-12 (GND) B - W-B Driver door power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on Driver Door Window Only)


*1: for LHD

*2: for RHD


a.
B276285C28
0.885,0.135 1.292,0.406 0.406,0.271 1.802,0.146 2.208,0.417 0.406,0.271 1,0.198 1.313,0.396 0.313,0.198 10 false K5 1.344,0.188 1.656,0.385 0.313,0.198 10 false *A 1.896,0.198 2.208,0.396 0.313,0.198 10 false J11 2.281,0.198 2.594,0.396 0.313,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the K5*1 or J11*2 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K5-7 (B) - K5-1 (E) LA-GR - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
K5-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J11-7 (B) - J11-9 (E) LA-GR - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
J11-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K5*1 or J11*2 power window regulator master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition

*: for Double Cab

K5-6 (U) - K5-1 (E) B - W-B Driver door power window motor up output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pulled halfway up (Manual operation) Below 1 V
K5-4 (A) - K5-1 (E) SB - W-B Driver door power window motor auto up output Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, driver door power window switch fully pulled up (AUTO UP position) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Driver door power window motor auto down output Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window switch fully pushed down (AUTO DOWN position) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
K5-3 (D) - K5-1 (E) P - W-B Driver door power window motor down output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pushed halfway down (Manual operation) Below 1 V
K5-10 (U) - K5-1 (E) LA-R - W-B Front passenger door power window motor up output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pulled up (Manual operation) Below 1 V
K5-18 (D) - K5-1 (E) LA-G - W-B Front passenger door power window motor down output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pushed down (Manual operation) Below 1 V
K5-12 (U) - K5-1 (E)* LA-Y - W-B Rear door LH power window motor up output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pulled up (Manual operation) Below 1 V
K5-13 (D) - K5-1 (E)* LA-P - W-B Rear door LH power window motor down output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pushed down (Manual operation) Below 1 V
K5-15 (U) - K5-1 (E)* LA-B - W-B Rear door RH power window motor up output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pulled up (Manual operation) Below 1 V
K5-16 (D) - K5-1 (E)* LA-V - W-B Rear door RH power window motor down output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pushed down (Manual operation) Below 1 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition

*: for Double Cab

J11-3 (U) - J11-9 (E) B - W-B Driver door power window motor up output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pulled halfway up (Manual operation) Below 1 V
J11-4 (A) - J11-9 (E) SB - W-B Driver door power window motor auto up output Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, driver door power window switch fully pulled up (AUTO UP position) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Driver door power window motor auto down output Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window switch fully pushed down (AUTO DOWN position) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J11-6 (D) - J11-9 (E) P - W-B Driver door power window motor down output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pushed halfway down (Manual operation) Below 1 V
J11-10 (U) - J11-9 (E) LA-R - W-B Front passenger door power window motor up output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pulled up (Manual operation) Below 1 V
J11-18 (D) - J11-9 (E) LA-G - W-B Front passenger door power window motor down output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pushed down (Manual operation) Below 1 V
J11-12 (U) - J11-9 (E)* LA-Y - W-B Rear door LH power window motor up output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pulled up (Manual operation) Below 1 V
J11-13 (D) - J11-9 (E)* LA-P - W-B Rear door LH power window motor down output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pushed down (Manual operation) Below 1 V
J11-15 (U) - J11-9 (E)* LA-B - W-B Rear door RH power window motor up output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pulled up (Manual operation) Below 1 V
J11-16 (D) - J11-9 (E)* LA-V - W-B Rear door RH power window motor down output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pushed down (Manual operation) Below 1 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Entry and Start System)


a.
B187997N69
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false J9

Disconnect the J9 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

J9-1 (GND) - Body ground W-B - Body ground*1
LA-W - Body ground*2
Ground Always Below 1 Ω
J9-2 (B) - Body ground GR - Body ground*1
LA-GR - Body ground*2
Power supply Always 11 to 14 V


c.

Reconnect the J9 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-4 (AUTO) - J9-1 (GND) L - W-B Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
J9-7 (DOWN) - J9-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
J9-10 (UP) - J9-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-7 (DOWN) - J9-1 (GND) P - LA-W Power window motor DOWN input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J9-10 (UP) - J9-1 (GND) B - LA-W Power window motor UP input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, power window master switch (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Only, RHD)


a.
B187997N71
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false J9

Disconnect the J9 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J9-2 (B) - Body ground GR - Body ground Power supply Always 11 to 14 V


c.

Reconnect the J9 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-7 (DOWN) - J9-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J9-10 (UP) - J9-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, power window master switch (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Entry and Start System)


a.
B187997N60
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false K9

Disconnect the K9 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

K9-1 (GND) - Body ground LA-W - Body ground*1
W-B - Body ground*2
Ground Always Below 1 Ω
K9-2 (B) - Body ground LA-GR - Body ground*1
GR - Body ground*2
Power supply Always 11 to 14 V


c.

Reconnect the K9 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-7 (DOWN) - K9-1 (GND) P - LA-W Power window motor DOWN input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) B - LA-W Power window motor UP input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, power window master switch (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-4 (AUTO) - K9-1 (GND) L - W-B Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
K9-7 (DOWN) - K9-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Only, LHD)


a.
B187997N72
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false K9

Disconnect the K9 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K9-2 (B) - Body ground GR - Body ground Power supply Always 11 to 14 V


c.

Reconnect the K9 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-7 (DOWN) - K9-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, power window master switch (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Entry and Start System)


a.
B187997N61
1.479,0.302 1.906,0.563 0.427,0.26 1.594,0.365 1.885,0.552 0.292,0.188 10 false M4

Disconnect the M4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M4-2 (B) - Body ground L - Body ground Power supply Always 11 to 14 V


c.

Reconnect the M4 rear power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
M4-4 (AUTO) - M4-1 (GND) R - W-B Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for Rear LH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for Rear LH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Entry and Start System)


a.
B187997N62
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false L4

Disconnect the L4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
L4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L4-2 (B) - Body ground G - Body ground Power supply Always 11 to 14 V


c.

Reconnect the L4 rear power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
L4-4 (AUTO) - L4-1 (GND) R - W-B Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for Rear RH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for Rear RH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY ECU


E317657C05
0.594,3.865 0.927,4.104 0.333,0.24 1.99,3.865 2.323,4.104 0.333,0.24 3.458,3.865 3.792,4.104 0.333,0.24 4.844,3.865 5.177,4.104 0.333,0.24 6.198,3.865 6.531,4.104 0.333,0.24 1.969,5.063 2.302,5.302 0.333,0.24 3.333,5.063 3.667,5.302 0.333,0.24 4.729,5.063 5.063,5.302 0.333,0.24 6.198,5.063 6.531,5.302 0.333,0.24 0.604,6.448 0.938,6.688 0.333,0.24 1.938,6.448 2.271,6.688 0.333,0.24 3.375,6.448 3.708,6.688 0.333,0.24 4.833,6.448 5.167,6.688 0.333,0.24 6.208,6.438 6.542,6.677 0.333,0.24 3.344,7.708 3.677,7.948 0.333,0.24 0.552,4.854 0.896,5.042 0.344,0.188 0.552,5.104 0.896,5.292 0.344,0.188 0.104,0.052 0.417,0.292 0.313,0.24 12 false *1 0.75,0.938 1.063,1.135 0.313,0.198 10 false 2L 0.729,1.281 1.042,1.479 0.313,0.198 10 false 2M 0.74,1.667 1.052,1.865 0.313,0.198 10 false 2D 0.74,2.031 1.052,2.229 0.313,0.198 10 false 2K 0.729,2.375 1.042,2.573 0.313,0.198 10 false 2C 0.615,3.01 1.104,3.219 0.49,0.208 10 false 2A (*A) 1.281,3.104 1.594,3.302 0.313,0.198 10 false 2B 3.333,0.896 3.49,1.094 0.156,0.198 10 false A 6.375,0.583 6.688,0.781 0.313,0.198 10 false 2Q 6.396,0.927 6.708,1.125 0.313,0.198 10 false 2J 6.385,1.281 6.698,1.479 0.313,0.198 10 false 2P 6.385,1.656 6.698,1.854 0.313,0.198 10 false 2N 6.385,2 6.698,2.198 0.313,0.198 10 false 2G 6.396,2.375 6.708,2.573 0.313,0.198 10 false 2H 5.865,2.927 6.177,3.125 0.313,0.198 10 false 2F 6.375,2.99 6.688,3.188 0.313,0.198 10 false 2E 0.698,3.906 1.01,4.104 0.313,0.198 10 false 2L 2.063,3.906 2.375,4.104 0.313,0.198 10 false 2M 3.552,3.896 3.865,4.094 0.313,0.198 10 false 2D 4.917,3.906 5.229,4.104 0.313,0.198 10 false 2K 6.271,3.906 6.594,4.125 0.323,0.219 10 false 2C 0.635,5.125 0.948,5.323 0.313,0.198 10 false 2R 2.042,5.094 2.354,5.292 0.313,0.198 10 false 2B 3.406,5.104 3.719,5.302 0.313,0.198 10 false 2Q 4.823,5.094 5.135,5.292 0.313,0.198 10 false 2J 6.292,5.104 6.604,5.302 0.313,0.198 10 false 2P 0.688,6.479 1,6.677 0.313,0.198 10 false 2N 2.021,6.479 2.333,6.677 0.313,0.198 10 false 2G 3.458,6.479 3.771,6.677 0.313,0.198 10 false 2H 4.927,6.479 5.24,6.677 0.313,0.198 10 false 2F 6.292,6.469 6.604,6.667 0.313,0.198 10 false 2E 3.469,7.74 3.625,7.938 0.156,0.198 10 false A 0.635,4.875 0.948,5.073 0.313,0.198 10 false 2A 0.958,4.865 1.271,5.063 0.313,0.198 10 false (*A) 0.979,5.115 1.292,5.313 0.313,0.198 10 false (*B) 0.615,3.188 1.125,3.365 0.51,0.177 10 false 2R (*B)
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly - -


E317658C05
2.24,3.344 2.625,3.583 0.385,0.24 4.563,3.344 4.948,3.583 0.385,0.24 0.125,0.073 0.438,0.365 0.313,0.292 12 false *1 5.76,1.531 6.219,1.729 0.458,0.198 10 false G28 5.76,2.021 6.219,2.219 0.458,0.198 10 false G27 2.313,3.385 2.771,3.583 0.458,0.198 10 false G28 4.625,3.385 5.083,3.583 0.458,0.198 10 false G27
*1 Body ECU - -


a.

Remove the body ECU from the instrument panel junction block assembly.



b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
A-1 (GND) - Body ground None - Body ground Ground Always Below 1 Ω
A-6 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
A-7 (IG) - Body ground None - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Install the body ECU to the instrument panel junction block assembly.



d.

Measure the voltage and waveform according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G27-14 (PCTY) - Body ground LG - Body ground Front passenger door courtesy light switch input Front passenger door open Below 1 V
Front passenger door closed Pulse generation
2L-4 (DCTY) - Body ground R - Body ground Driver door courtesy light switch input Driver door open Below 1 V
Driver door closed Pulse generation