WIRELESS DOOR LOCK CONTROL SYSTEM
The wireless door lock control system can be used to lock and unlock all doors from a distance. The system is controlled by a door control transmitter which sends radio waves to the door control receiver. The system performs an ID code identification process and operates the door lock control.
FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Door control transmitter | ·
Has the lock, unlock and alarm*1 switches. ·
Transmits weak radio waves (recognition codes and function codes) to the door control receiver. |
| Door control receiver | Receives weak radio waves from the door control transmitter and sends them to the body ECU. |
| Front door courtesy light switch assembly LH
Front door courtesy light switch assembly RH Rear door courtesy light switch assembly LH*2 Rear door courtesy light switch assembly RH*2 Upper access panel lock assembly LH*3 Upper access panel lock assembly RH*3 Lower access panel lock assembly LH*3 Lower access panel lock assembly RH*3 |
·
Placed on each door. ·
Turns on when a door is opened and turns off when it is closed. ·
Outputs door status signals (open or closed) to the body ECU. |
| Unlock warning switch assembly | Detects if the key is inserted in the ignition key cylinder or not. |
| Front door lock assembly LH*4
Front door lock assembly RH*5 |
·
The built-in motor locks or unlocks the door. ·
The built-in unlock detection switch detects the door status (locked or unlocked) and outputs a signal to the body ECU. This switch turns off when the door is locked and turns on when the door is unlocked. |
| Front door lock assembly RH*4
Front door lock assembly LH*5 Rear door lock assembly LH*2 Rear door lock assembly RH*2 |
The built-in motor locks or unlocks the door. |
| Body ECU | Sends wireless door lock control signals in response to the code data from the door control receiver and signals from each switch. |
*1: w/ Alarm Switch
*2: for Double Cab
*3: for Smart Cab
*4: for LHD
*5: for RHD
SYSTEM FUNCTION
The door control transmitter has the lock and unlock and alarm* switches. Operating these switches activates each function.
The wireless door lock control system has the following functions:
| Function | Operation |
|---|---|
| All door lock | Pressing the lock switch locks all doors. |
| All door unlock | Pressing the unlock switch unlocks all doors. |
| Automatic lock | If none of the doors are opened within 30 seconds after they are unlocked by wireless door lock control, all doors will lock again automatically. |
| Remote alarm function* | Pressing the alarm switch of the transmitter for more than approximately 0.8 seconds causes the following alarms to activate:
·
Sounds the horns. ·
Flashes the hazard warning lights and side turn signal lights. |
| Answer back (Hazard warning light) | ·
When the doors are locked by wireless operation, the hazard warning lights flash once. ·
When the doors are unlocked by wireless operation, the hazard warning lights flash twice. |
| Illuminated entry | When all doors are locked, pressing the unlock switch causes the interior lights to come on simultaneously with the unlock operation. |
| Self-diagnostic mode | If the door control receiver receives normal radio waves from the door control transmitter when the system is in diagnostic mode, it flashes the interior lights in a normal pattern that corresponds to the function of each switch. |
| Transmitter recognition code registration | Enables registration (writing and storing) of door control transmitter recognition codes in the EEPROM that is contained in the door control receiver. |
*: w/ Alarm Switch
TRANSMITTER RECOGNITION CODE REGISTRATION FUNCTION
The table below shows the 4 ID registration function modes. The codes are electronically registered (written and stored) in the EEPROM that is contained in the door control receiver.
| Mode | Function |
|---|---|
| Add mode | Adds a newly received code while preserving any previously registered codes.
This mode is used when adding a new door control transmitter. If the maximum registration number is exceeded, the oldest one is cleared first. |
| Rewrite mode | Clears all previously registered codes and registers only newly input codes. |
| Confirmation mode | Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist. |
| Prohibition mode | Clears all registered codes and disables the wireless door lock function.
This mode is used when the door control transmitter is lost. |
CONDITIONS THAT WIRELESS FUNCTIONS DO NOT OPERATE
The lock function will not operate when either of the following conditions is met:
Any of the doors are open.
The key is inserted in the ignition key cylinder.
The unlock function will not operate when the following condition is met:
The key is inserted in the ignition key cylinder.