Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0184499 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter and sends these signals to the body ECU. The body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

B405236E03
4.823,0.76 5.281,0.958 0.458,0.198 10 false PRG 4.844,1.469 5.302,1.667 0.458,0.198 10 false RDA 4.583,0.677 5.042,0.875 0.458,0.198 10 false 9 4.531,1.385 4.99,1.583 0.458,0.198 10 false 16 3.573,0.667 4.031,0.865 0.458,0.198 10 false PRG 3.979,0.677 4.438,0.875 0.458,0.198 10 false 3 3.552,1.385 4.01,1.583 0.458,0.198 10 false RDA 3.979,1.385 4.438,1.583 0.458,0.198 10 false 2 1.823,0.688 2.292,1.063 0.469,0.375 10 false ECU-B NO.1 0.521,0.51 1.427,0.75 0.906,0.24 10 false from Battery 2.448,1.385 2.906,1.583 0.458,0.198 10 false GND 2.448,0.5 2.906,0.698 0.458,0.198 10 false +B 2.229,0.406 2.688,0.604 0.458,0.198 10 false 5 2.25,1.385 2.708,1.583 0.458,0.198 10 false 1 2.531,2.146 2.99,2.344 0.458,0.198 10 false G23 2.542,2.292 4.438,2.531 1.896,0.24 10 false Door Control Receiver 4.844,2.719 5.302,2.917 0.458,0.198 10 false KSW 3.135,0.25 3.594,0.448 0.458,0.198 10 false +B 5.896,2.427 6.354,2.625 0.458,0.198 10 false +B 4.604,2.719 5.063,2.917 0.458,0.198 10 false 8 2.094,2.719 2.552,2.917 0.458,0.198 10 false 1 0.583,2.719 1.042,2.917 0.458,0.198 10 false 2 0.396,3.094 0.854,3.292 0.458,0.198 10 false G2 0.406,3.25 3.01,3.5 2.604,0.25 10 false Unlock Warning Switch Assembly 5.333,3.198 6.229,3.427 0.896,0.229 10 false G27 5.344,3.354 6.24,3.583 0.896,0.229 10 false Body ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.*1

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

*1: w/ Automatic Light Control System

*2: w/ Door Control Battery




PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Locked doors unlock



Result:
Proceed to
OK
NG



OK

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - BODY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - BODY ECU AND BODY GROUND)
a.

Disconnect the G2 unlock warning switch assembly connector.


b.

Disconnect the G27 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-1 - G27-8 (KSW) Always Below 1 Ω
G2-2 - Body ground Always Below 1 Ω
G2-1 or G27-8 (KSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.SWITCH TO SELF-DIAGNOSTIC MODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.SWITCH TO SELF-DIAGNOSTIC MODE
a.

Switch to self-diagnostic mode by operating the ignition key cylinder.

i.

Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.


ii.

Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.


iii.

Within 30 seconds of turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and off.

CAUTION:

If the system cannot enter self-diagnostic mode, the system returns to normal mode.


HINT:
·

Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.

·

Do not lock or unlock doors during self-diagnostic mode.




iv.
B220865E58
0.125,0.031 2.229,0.313 2.104,0.281 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false On 0.646,1.688 0.969,1.948 0.323,0.26 10 false Off 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light flash pattern.



Result:
Proceed to
NEXT



NEXT

5.CHECK BY SELF-DIAGNOSTIC MODE
5.CHECK BY SELF-DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B357193E22
0.135,0.104 2.948,0.583 2.813,0.479 12 false Interior Light Output: 0.26,1.021 3.948,1.271 3.688,0.25 10 false Normal Wave (A) (Lock/Unlock/Alarm* Switch): 0.458,2.177 0.917,2.375 0.458,0.198 10 false Off 0.448,1.802 0.906,2 0.458,0.198 10 false On 1.208,2.604 1.667,2.802 0.458,0.198 10 false T1 1.719,2.615 2.177,2.813 0.458,0.198 10 false T2 0.677,3.198 3.823,3.438 3.146,0.24 10 false T1: 0.25 seconds 0.677,3.583 3.823,3.823 3.146,0.24 10 false T2: 0.5 seconds 4.031,0.448 6.323,0.646 2.292,0.198 10 false Unmatching Recognition Code (B): 4.26,0.99 4.719,1.188 0.458,0.198 10 false On 4.281,1.365 4.74,1.563 0.458,0.198 10 false Off 4.917,1.844 6.51,2.094 1.594,0.25 10 false Wave is being received 4.094,2.708 5.688,2.958 1.594,0.25 10 false No Diagnostic Output (C): 4.25,3.188 4.708,3.385 0.458,0.198 10 false Off 0.396,4.354 2.594,4.583 2.198,0.229 10 false *: w/ Alarm Switch


Result:
Result Proceed to
No diagnostic outputs A
Unmatching recognition code is output B
Normal wave (light flash pattern) is output C



A

6.CHECK DOOR CONTROL RECEIVER (RESPONSE)

B

17.CHECK REGISTER RECOGNITION CODE

C

6.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter from another vehicle.


b.

Press and hold down the door control transmitter switch.


c.

Check that an unmatching recognition code is output.


Result:
Result Proceed to
Unmatching recognition code is not output A
Unmatching recognition code is output B



A

7.CHECK WAVE ENVIRONMENT

B

14.INSPECT TRANSMITTER BATTERY (VOLTAGE)
7.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter near the door control receiver, and perform a wireless operation check.

HINT:
·

When the door control transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




Result:
Result Proceed to
Wireless functions do not operate properly A
Wireless functions operate properly B



A

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

B

END (AFFECTED BY WAVE INTERFERENCE)

8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
B405237C02
1.417,0.135 1.917,0.385 0.5,0.25 0.75,1.75 1,1.75 1,1.75 1.25,1.333 true 2.698,1.75 2.448,1.75 2.448,1.75 2.198,1.333 true 1.531,0.177 1.99,0.375 0.458,0.198 10 false G23 0.417,1.667 0.875,1.865 0.458,0.198 10 false GND 2.75,1.646 3.208,1.844 0.458,0.198 10 false +B 0.156,0.135 0.615,0.333 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Door Control Receiver)


Disconnect the door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-5 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.
B405238C02
1.438,0.125 1.938,0.375 0.5,0.25 2.5,2 2.25,2 2.25,2 1.917,1.229 true 2.542,1.906 3,2.104 0.458,0.198 10 false RDA 1.552,0.167 2.01,0.365 0.458,0.198 10 false G23 0.167,0.135 0.625,0.333 0.458,0.198 10 false *a
*a Component with harness connected
(Door Control Receiver)


Connect the door control receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-2 (RDA) - Body ground Ignition switch off, all doors closed and door control transmitter switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter switch pressed Pulse generation



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BODY ECU)

NG

REPLACE DOOR CONTROL RECEIVER

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BODY ECU)
a.

Disconnect the G23 door control receiver connector.


b.

Disconnect the G27 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-2 (RDA) - G27-16 (RDA) Always Below 1 Ω
G23-3 (PRG) - G27-9 (PRG) Always Below 1 Ω
G23-2 (RDA) or G27-16 (RDA) - Body ground Always 10 kΩ or higher
G23-3 (PRG) or G27-9 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.REGISTER RECOGNITION CODE
12.REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

13.CHECK DOOR CONTROL RECEIVER (OPERATION)
13.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

14.INSPECT TRANSMITTER BATTERY (VOLTAGE)

Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER

NG

15.REPLACE TRANSMITTER BATTERY
15.REPLACE TRANSMITTER BATTERY

Result:
Proceed to
NEXT



NEXT

16.CHECK BY SELF-DIAGNOSTIC MODE
16.CHECK BY SELF-DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B357193E22
0.135,0.104 2.948,0.583 2.813,0.479 12 false Interior Light Output: 0.26,1.021 3.948,1.271 3.688,0.25 10 false Normal Wave (A) (Lock/Unlock/Alarm* Switch): 0.458,2.177 0.917,2.375 0.458,0.198 10 false Off 0.448,1.802 0.906,2 0.458,0.198 10 false On 1.208,2.604 1.667,2.802 0.458,0.198 10 false T1 1.719,2.615 2.177,2.813 0.458,0.198 10 false T2 0.677,3.198 3.823,3.438 3.146,0.24 10 false T1: 0.25 seconds 0.677,3.583 3.823,3.823 3.146,0.24 10 false T2: 0.5 seconds 4.031,0.448 6.323,0.646 2.292,0.198 10 false Unmatching Recognition Code (B): 4.26,0.99 4.719,1.188 0.458,0.198 10 false On 4.281,1.365 4.74,1.563 0.458,0.198 10 false Off 4.917,1.844 6.51,2.094 1.594,0.25 10 false Wave is being received 4.094,2.708 5.688,2.958 1.594,0.25 10 false No Diagnostic Output (C): 4.25,3.188 4.708,3.385 0.458,0.198 10 false Off 0.396,4.354 2.594,4.583 2.198,0.229 10 false *: w/ Alarm Switch


Result:
Result Proceed to
Normal wave (light flash pattern) is output A
Unmatching recognition code is output B
No diagnostic outputs



A

END (TRANSMITTER BATTERY WAS DEFECTIVE)

B

REPLACE DOOR CONTROL TRANSMITTER

17.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>REGISTRATION

OK:

Recognition code can be registered.



Result:
Proceed to
OK
NG



OK

NG