Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM3250E _51 Engine / Hybrid System _038022 2TR-FE ENGINE MECHANICAL _0184667 REAR CRANKSHAFT OIL SEAL A

2TR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.
A346815N01
1.969,1.313 2.844,2.177 2.844,2.177 2.281,0.677 true 2.042,2.667 2.563,2.667 2.563,2.667 2.229,2.958 true 2.74,2.229 3.073,2.417 0.333,0.188 10 false SST 2.615,2.573 2.948,2.76 0.333,0.188 10 false SST

Apply a light coat of MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the rear engine oil seal.

·

Do not allow MP grease to contact the dust seal.




b.

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the rear engine oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A348628C01
1.563,1.917 1.75,2.104 0.188,0.188 10 false *a
*a Hold


Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A346816C01
1,2.323 1.156,2.323 1.156,2.323 1.333,2.604 false 2.729,2.24 2.552,2.24 2.552,2.24 2.427,2.531 false 2.292,1.135 2.115,1.135 2.115,1.135 1.99,1.427 false 0.802,2.219 1,2.417 0.198,0.198 10 false *1 2.323,1.042 2.531,1.229 0.208,0.188 10 false *2 2.76,2.135 2.958,2.344 0.198,0.208 10 false *3
*1 Front Drive Plate Spacer
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
V100135

Transmission Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the rear drive plate spacer and drive plate and ring gear sub-assembly are not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.

Clean the bolts and bolt holes.


d.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A346813N01
1.438,0.885 1.563,1.063 0.125,0.177 10 true 2 2.688,1.26 2.813,1.438 0.125,0.177 10 true 1 1.677,1.719 1.802,1.896 0.125,0.177 10 true 3 2.552,0.521 2.677,0.698 0.125,0.177 10 true 4 1.406,1.292 1.531,1.469 0.125,0.177 10 true 5 2.708,0.906 2.833,1.083 0.125,0.177 10 true 6 1.656,0.521 1.781,0.698 0.125,0.177 10 true 7 2.521,1.583 2.646,1.76 0.125,0.177 10 true 8 2.104,1.792 2.229,1.969 0.125,0.177 10 true 9 2.052,0.385 2.26,0.563 0.208,0.177 10 true 10

Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate and ring gear sub-assembly.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A348628C01
1.563,1.917 1.75,2.104 0.188,0.188 10 false *a
*a Hold


Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolt holes.


c.
A346812N01
1.396,0.875 1.51,1.052 0.115,0.177 10 true 2 2.615,1.25 2.729,1.427 0.115,0.177 10 true 1 1.615,1.719 1.729,1.896 0.115,0.177 10 true 3 2.5,0.552 2.615,0.729 0.115,0.177 10 true 4 1.375,1.281 1.49,1.458 0.115,0.177 10 true 5 2.656,0.917 2.771,1.094 0.115,0.177 10 true 6 1.615,0.552 1.729,0.729 0.115,0.177 10 true 7 2.438,1.583 2.552,1.76 0.115,0.177 10 true 8 2.052,1.781 2.167,1.958 0.115,0.177 10 true 9 2,0.385 2.198,0.563 0.198,0.177 10 true 10

Install the flywheel sub-assembly with the new 10 bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)


d.

Mark the top of the bolts with paint.


e.

Tighten the 10 bolts 90° in the same sequence.


f.

Check that the paint marks are now at a 90° angle to the top.


Hide 31250 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 6.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 33030 8.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)