Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184916 IMMOBILISER SYSTEM(w/o Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B354639E03
3.333,0.583 3.833,0.833 0.5,0.25 3.458,0.615 3.917,0.813 0.458,0.198 10 false G16

a.

Disconnect the G16 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G16-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G16-1 (+B) - G16-5 (GND) Input L - BR Battery Always 11 to 14 V +B
G16-2 (IG) - G16-5 (GND) Input P - BR Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
G16-3 (KSW) - G16-5 (GND) Input G - BR Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G16 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G16-8 (IND) - G16-5 (GND) Output Y - BR Security indicator light signal No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
G16-9 (D) - G16-5 (GND) Input/Output R - BR DLC3 communication Without communication Below 1 V -
During communication Pulse generation
G16-4 (ANT1) - G16-5 (GND) Input/Output Y - BR Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
G16-15 (ANT2) - G16-5 (GND) Input/Output W - BR Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
G16-12 (EFII) - G16-5 (GND) Input Y - BR ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
E/G Start Permission
G16-13 (EFIO) - G16-5 (GND) Output B - BR ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection G16-4 (ANT1) - G16-5 (GND)
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection G16-15 (ANT2) - G16-5 (GND)
Tool Setting 2 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G16-12 (EFII) - G16-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G16-13 (EFIO) - G16-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1TR-FE, 2TR-FE)


A347038C03
1,2.167 1.417,2.417 0.417,0.25 2.5,2.167 2.917,2.417 0.417,0.25 4.219,2.167 4.667,2.417 0.448,0.25 5.583,2.167 6,2.417 0.417,0.25 0.698,0.313 1.094,0.583 0.396,0.271 2,0.313 2.448,0.573 0.448,0.26 3.417,0.344 3.865,0.604 0.448,0.26 4.813,0.313 5.26,0.583 0.448,0.271 6.083,0.323 6.563,0.583 0.479,0.26 0.073,0.208 0.385,0.406 0.313,0.198 12 false *A 0.094,2.063 0.406,2.26 0.313,0.198 12 false *B 0.771,0.375 1.229,0.573 0.458,0.198 10 false C52 2.083,0.375 2.542,0.573 0.458,0.198 10 false C53 3.51,0.375 3.969,0.573 0.458,0.198 10 false C54 4.875,0.365 5.333,0.563 0.458,0.198 10 false G45 6.167,0.375 6.625,0.573 0.458,0.198 10 false G46 1.094,2.208 1.552,2.406 0.458,0.198 10 false C52 2.583,2.208 3.042,2.406 0.458,0.198 10 false C53 4.302,2.208 4.76,2.406 0.458,0.198 10 false G45 5.667,2.208 6.125,2.406 0.458,0.198 10 false G46
*A for Automatic Transmission Models *B for Manual Transmission Models


a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C52-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C52-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C52-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C53-5 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C52-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G46-1 (+B) - C52-3 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G46-2 (+B2) - C52-3 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
G46-3 (BATT) - C52-3 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G45-9 (IMO) - C52-3 (E1) Output Y - W-B Transponder key ECU assembly output signal Ignition switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G45-10 (IMI) - C52-3 (E1) Input B - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G45-9 (IMO) - C52-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G45-10 (IMI) - C52-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1KD-FTV, 2KD-FTV)


A254878E04
1.208,0.406 1.615,0.646 0.406,0.24 2.729,0.406 3.135,0.646 0.406,0.24 4.292,0.406 4.698,0.646 0.406,0.24 5.76,0.406 6.167,0.646 0.406,0.24 1.281,0.448 1.594,0.625 0.313,0.177 10 false C55 2.802,0.448 3.115,0.625 0.313,0.177 10 false C56 4.365,0.448 4.677,0.625 0.313,0.177 10 false G83 5.833,0.448 6.146,0.625 0.313,0.177 10 false G84

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C56-7 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C55-7 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C55-6 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G83-2 (BATT) - C56-7 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G84-1 (+B) - C56-7 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G83-29 (IMO) - C56-7 (E1) Output Y - W-B Transponder key ECU assembly output signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G83-30 (IMI) - C56-7 (E1) Input B - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G83-29 (IMO) - C56-7 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G83-30 (IMI) - C56-7 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GD-FTV, 2GD-FTV)


A340466E09
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 1.844,0.469 2.156,0.667 0.313,0.198 10 false C58 0.635,0.469 0.948,0.667 0.313,0.198 10 false C57 2.938,0.469 3.25,0.667 0.313,0.198 10 false C59 3.99,0.469 4.302,0.667 0.313,0.198 10 false C60 5.083,0.469 5.396,0.667 0.313,0.198 10 false G85 6.25,0.469 6.563,0.667 0.313,0.198 10 false G86

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C60-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C60-3 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C59-3 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C60-4 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C60-2 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G86-1 (BATT) - C60-1 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G86-2 (+B) - C60-1 (E1) Input L - W-B +B power supply Ignition switch ON 11 to 14 V -
G86-3 (+B2) - C60-1 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
G86-17 (IMO) - C60-1 (E1) Output Y - W-B Transponder key ECU assembly output signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G86-16 (IMI) - C60-1 (E1) Input B - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G86-17 (IMO) - C60-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G86-16 (IMI) - C60-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GR-FE)


A225776E20
0.625,0.427 0.979,0.646 0.354,0.219 1.677,0.427 2.031,0.646 0.354,0.219 3.135,0.427 3.49,0.646 0.354,0.219 4.198,0.427 4.552,0.646 0.354,0.219 5.25,0.427 5.604,0.646 0.354,0.219 6.313,0.427 6.667,0.646 0.354,0.219 0.688,0.458 1.063,0.688 0.375,0.229 10 false G87 1.729,0.458 2.104,0.688 0.375,0.229 10 false G88 3.188,0.458 3.563,0.688 0.375,0.229 10 false C15 4.25,0.458 4.625,0.688 0.375,0.229 10 false C14 5.302,0.458 5.677,0.688 0.375,0.229 10 false C13 6.365,0.458 6.74,0.688 0.375,0.229 10 false C12

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C13-12 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C13-29 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C13-23 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C12-16 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C12-14 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G87-23 (+B) - C13-12 (E1) Input L - BR +B power supply Ignition switch ON 11 to 14 V -
G87-22 (+B2) - C13-12 (E1) Input B - BR +B power supply Ignition switch ON 11 to 14 V -
G87-24 (BATT) - C13-12 (E1) Input Y - BR +B power supply Always 11 to 14 V -
G88-8 (IMO) - C13-12 (E1) Output Y - BR Transponder key ECU assembly output signal Ignition switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G88-10 (IMI) - C13-12 (E1) Input B - BR Transponder key ECU assembly input signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G88-8 (IMO) - C13-12 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G88-10 (IMI) - C13-12 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal