Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM3250E _55 Steering _038050 STEERING COLUMN _0185022 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


B118684C24
1.76,0.833 2.208,1.146 0.448,0.313 1.865,0.906 2.385,1.167 0.521,0.26 10 false G71 0.281,0.125 0.51,0.292 0.229,0.167 10 false *a
*a Component without harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
- -


a.

Measure the voltage, resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G71-1 (GND) - Body ground - W-B - Body ground Ground*2 Always Below 1 Ω -
G71-3 (IGE) - G71-1 (GND) Input L - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*1

·

Steering lock unlocked in advance by carrying key and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Pulse generation (see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G71-4 (SLP1) - G71-1 (GND) Output R - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start
·

Sensor Value


G71-5 (LIN) - G71-1 (GND) Input/Output V - W-B LIN communication line - -
Entry&Start
·

Steering Lock Start Cond


G71-6 (IG2) - G71-1 (GND) Input P - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator assembly)*2 Engine switch off → engine switch on (IG) Below 1 V → 11 to 14 V -
G71-7 (B) - Body ground Input W - Body ground Power source*2 Always 11 to 14 V -

*1: for Automatic Transmission

*2: When there is a problem with the power source input, the certification ECU (smart key ECU assembly) may store DTC B2786.


NOTICE:

There is 1 motor and 2 sensors built into the steering lock actuator assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.



*: for Automatic Transmission



i.
C221561C35
0.292,0.396 1.698,0.563 1.406,0.167 1.521,1.583 2.49,1.708 0.969,0.125 2.292,0.448 2.719,0.604 0.427,0.156 2.083,1.708 2.167,1.99 2.167,1.99 2.219,1.99 true 1.698,0.438 2.813,0.198 2.813,0.198 2.885,0.198 true 2.802,0.198 2.604,0.448 true 2.917,1.583 3.385,1.958 0.469,0.375 10 false GND 2.271,1.906 2.76,2.052 0.49,0.146 10 false *b 2.948,0.104 3.313,0.333 0.365,0.229 10 false *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform

Item Content
Tester Connection G71-3 (IGE) - G71-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating