Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0185023 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

SMART fuse

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Turn the engine switch on (IG).
HINT:

To turn the engine switch on (IG), carry an electrical key transmitter sub-assembly and press the engine switch twice with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only detected while a malfunction is present and the engine switch is on (IG).

*2: for Automatic Transmission

*3: for Manual Transmission


HINT:
·

The IG circuit activates the No. 1 ignition relay and No. 2 ignition relay.

·

After the IG circuit turns on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Engine switch is on (IG) ○ ○
Malfunction Status The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning. ○ -
The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning. - ○
Detection Time - -
Trip Count 1-trip 1-trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit


Starting Control
·

Ignition


-

WIRING DIAGRAM

C325657E02
0.073,0.667 0.938,0.875 0.865,0.208 10 false from Battery 1.448,0.823 2.219,1.021 0.771,0.198 10 false SMART 2.188,0.542 2.344,0.74 0.156,0.198 10 false 1 2.438,0.677 2.75,0.875 0.313,0.198 10 false +B 3.135,1.25 3.552,1.458 0.417,0.208 10 false IG1D 2.427,3.073 2.583,3.271 0.156,0.198 10 false E 2.135,2.958 2.448,3.156 0.313,0.198 10 false 10 2.26,4 3.813,4.385 1.552,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.26,3.833 2.719,4.031 0.458,0.198 10 false G69 3.573,1.25 3.885,1.448 0.313,0.198 10 false 20 6.375,0.948 6.958,1.135 0.583,0.188 10 false to Fuses 6.354,2.542 6.979,2.76 0.625,0.219 10 false to Fuses 5.688,0.375 6.708,0.573 1.021,0.198 10 false from AM1 Fuse 4.771,0.844 4.927,1.042 0.156,0.198 10 false 5 5.573,0.833 5.729,1.031 0.156,0.198 10 false 3 4.771,1.26 4.927,1.458 0.156,0.198 10 false 1 5.573,1.229 5.729,1.427 0.156,0.198 10 false 2 4.948,1.698 5.615,1.917 0.667,0.219 10 false IG1 NO. 1 5.104,3.302 5.563,3.5 0.458,0.198 10 false IG2 4.771,2.844 4.927,3.042 0.156,0.198 10 false 1 5.573,2.865 5.729,3.063 0.156,0.198 10 false 2 5.573,2.427 5.729,2.625 0.156,0.198 10 false 3 4.771,2.427 4.927,2.625 0.156,0.198 10 false 5 5.688,3.75 7.115,3.958 1.427,0.208 10 false from AM2 NO. 2 Fuse 2.573,1.26 2.792,1.469 0.219,0.208 10 false IC 2.927,0.885 3.24,1.083 0.313,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B342622C22
1.5,0.25 1.917,0.5 0.417,0.25 0.573,1.115 0.333,1.75 true 0.26,0.26 0.573,0.417 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false G69 0.219,1.771 0.677,1.969 0.458,0.198 10 false +B
*a Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly))


Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B342622C23
1.5,0.25 1.927,0.5 0.427,0.25 2.813,1.146 3.083,1.75 true 0.271,0.25 0.583,0.406 0.313,0.156 10 false *a 1.583,0.302 2.042,0.5 0.458,0.198 10 false G69 3.063,1.792 3.219,1.99 0.156,0.198 10 false E
*a Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly))


Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-10 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

C332681C01
1.854,0.479 2.313,0.74 0.458,0.26 1.563,2.406 1.771,2.406 1.771,2.406 1.958,1.635 true 0.219,0.115 0.531,0.313 0.313,0.198 10 false *a 1.958,0.531 2.417,0.729 0.458,0.198 10 false G69 1.229,2.333 1.844,2.531 0.615,0.198 10 false IG1D
*a Component with harness connected (Certification ECU (Smart Key ECU Assembly)) - -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G69-20 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)