Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0185023 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

·

When the smart key cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG Relay Monitor(Inside)

·

IG Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After completing repairs, confirm that the problem does not occur.

·

The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.

·

The door control receiver is also related to interior verification.



HINT:
·

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

·

If the room oscillator does not recognize, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

The certification ECU (smart key ECU assembly) stores the operation history of the entry and start system and it can be read using the GTS.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Radio Wave Interference
Parameter Name Content
Operating Engine Switch / Key RF Signal Interference When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

Engine Start Inactive (radio wave interference)
Parameter Name Content
Operating Power Switch/Indoor oscillator LF Signal Interference When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

PROCEDURE

1.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

2.READ VALUE USING GTS (KEY LOW BATTERY)

B

12.INSPECT TRANSMITTER BATTERY

C

2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

OK:

"No" is displayed in the Data List.


Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125
Body Electrical > Starting Control > Clear DTCs
50002 221
Body Electrical > Power Source Control > Clear DTCs
50002 223

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221
Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY AND START SYSTEM (VEHICLE INTERIOR DETECTION)

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

4.CHECK ENTRY AND START SYSTEM (VEHICLE INTERIOR DETECTION)
a.

Get into the vehicle while carrying a different, previously-registered electrical key transmitter sub-assembly.


b.

for Automatic Transmission

Move the shift lever to P.


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for Automatic Transmission

*2: for Manual Transmission



Result:
Result Proceed to
Power source mode does not change A
Off → on (ACC) → on (IG) → off B



A

5.CHECK WIRELESS AND ENTRY FUNCTION

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

5.CHECK WIRELESS AND ENTRY FUNCTION
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK


b.

Check that the entry lock and unlock functions operate on each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



OK:

Wireless door lock, entry door lock and entry door unlock functions operate normally.


Result:
Proceed to
OK
NG



OK

6.CHECK PUSH START FUNCTION

NG

GO TO ENTRY AND START SYSTEM (ALL DOOR ENTRY LOCK/UNLOCK FUNCTIONS AND WIRELESS FUNCTIONS DO NOT OPERATE)

6.CHECK PUSH START FUNCTION
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT


b.
B406021C01
0.885,0.427 1.052,0.427 1.052,0.427 1.26,0.646 false 2.115,0.604 2.219,0.396 2.219,0.396 2.385,0.396 false 0.708,0.344 1.021,0.542 0.313,0.198 10 false *1 2.448,0.333 2.76,0.531 0.313,0.198 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


OK:

The power source mode changes.



Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

7.CHECK WAVE ENVIRONMENT

B

17.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/ CLUTCH SW)
7.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (rear floor).



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, parts installed by the dealer may cause wave interference. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



Result:
Result Proceed to
System cannot be operated A
System can be operated B



A

8.CHECK KEY DIAGNOSTIC MODE

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B406014C01
0.677,0.896 2.552,0.354 true 1.792,0.917 2.552,0.365 true 0.031,0.031 0.344,0.229 0.313,0.198 10 false *A 2.615,0.26 2.927,0.458 0.313,0.198 10 false *a
*A for Smart Cab
*a Inspection Point


B406015C01
0.667,0.844 2.5,0.333 true 1.781,0.854 2.51,0.344 true 0.031,0.031 0.344,0.229 0.313,0.198 10 false *A 2.542,0.26 2.854,0.458 0.313,0.198 10 false *a
*A for Double Cab
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.


ii.
B406017C01
0.646,0.583 2.49,0.26 true 1.844,0.573 2.5,0.271 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *A 2.563,0.177 2.875,0.375 0.313,0.198 10 false *a
*A for Smart Cab
*a Inspection Point


B406018C01
0.688,0.677 2.469,0.271 true 1.813,0.656 2.479,0.281 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *A 2.531,0.198 2.844,0.396 0.313,0.198 10 false *a
*A for Double Cab
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.



HINT:
·

If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

·

It is possible to check which indoor electrical key antenna assembly (front or rear) is operating by the sounding of the buzzer.

·

If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may be malfunctioning.



Result:
Result Proceed to
Front floor operation check fails A
Rear floor operation check fails B
The wireless buzzer sounds/does not sound for all indoor electrical key antenna assemblies C



A

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

B

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

C

16.CHECK CONNECTOR CONNECTION CONDITION
9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G74 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-31 (CLG1) - G74-1 (ANTE1) Always Below 1 Ω
G70-30 (CG1B) - G74-3 (CLGB) Always Below 1 Ω
G70-31 (CLG1) or G74-1 (ANTE1) - Body ground Always 10 kΩ or higher
G70-30 (CG1B) or G74-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Connect the G70 certification ECU (smart key ECU assembly) connector.


b.

Connect the G74 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Using an oscilloscope, check the waveform.

B345003C20
0.844,1.135 1.271,1.417 0.427,0.281 1.479,2.219 1.719,1.406 true 2.083,2.219 1.854,1.406 true 0.917,1.198 1.375,1.396 0.458,0.198 10 false G74 1.063,0.688 1.375,0.885 0.313,0.198 10 false *a 3.479,0.531 3.792,0.729 0.313,0.198 10 false *b 4.083,2.031 4.396,2.229 0.313,0.198 10 false *c 4.938,2.042 5.25,2.24 0.313,0.198 10 false *d 1.271,2.26 1.729,2.458 0.458,0.198 10 false CLGB 2.01,2.26 2.583,2.469 0.573,0.208 10 false ANTE1 3.49,1.302 3.885,1.479 0.396,0.177 10 false GND
*a Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform 1
*c Door open *d After approximately 30 seconds from when the door is closed


Standard Frequency:
Tester Connection Condition Tool Setting Specified Condition
G74-1 (ANTE1) - G74-3 (CLGB) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N9 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-6 (CLG2) - N9-1 (ANTE2) Always Below 1 Ω
G70-23 (CG2B) - N9-3 (CLGB) Always Below 1 Ω
G70-6 (CLG2) or N9-1 (ANTE2) - Body ground Always 10 kΩ or higher
G70-23 (CG2B) or N9-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Connect the G70 certification ECU (smart key ECU assembly) connector.


b.

Connect the N9 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Using an oscilloscope, check the waveform.

B345003C21
0.844,1.135 1.271,1.417 0.427,0.281 1.479,2.219 1.719,1.406 true 2.083,2.219 1.854,1.406 true 0.979,1.198 1.438,1.396 0.458,0.198 10 false N9 1.063,0.688 1.375,0.885 0.313,0.198 10 false *a 3.479,0.531 3.792,0.729 0.313,0.198 10 false *b 4.083,2.031 4.396,2.229 0.313,0.198 10 false *c 4.938,2.042 5.25,2.24 0.313,0.198 10 false *d 1.271,2.26 1.729,2.458 0.458,0.198 10 false CLGB 2.01,2.26 2.563,2.458 0.552,0.198 10 false ANTE2 3.49,1.302 3.885,1.479 0.396,0.177 10 false GND
*a Component with harness connected
(No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform 1
*c Door open *d After approximately 30 seconds from when the door is closed


Standard Frequency:
Tester Connection Condition Tool Setting Specified Condition
N9-1 (ANTE2) - N9-3 (CLGB) Procedure:
1.

All doors closed

2.

Engine switch off

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Door is open

5.

Door is closed

6.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

17.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/ CLUTCH SW)
a.

for Automatic Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.




b.

for Manual Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to help determine if the clutch start switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
OK:

The item in the Data List changes when the clutch pedal is depressed and released.




Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG (for Automatic Transmission)

28.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG (for Manual Transmission)

30.INSPECT CLUTCH START SWITCH ASSEMBLY
18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Connect the 2E and 2J instrument panel junction block assembly connectors.


c.

Read the Data List according to the display on the GTS.

C332681C03
1.854,0.479 2.313,0.74 0.458,0.26 1.563,2.406 1.771,2.406 1.771,2.406 1.885,1.625 true 2.563,2.438 2.406,2.438 2.406,2.438 1.958,1.646 true 0.219,0.115 0.531,0.313 0.313,0.198 10 false *a 1.958,0.531 2.417,0.729 0.458,0.198 10 false G69 1.167,2.333 1.781,2.531 0.615,0.198 10 false ACCD 2.604,2.365 3.219,2.563 0.615,0.198 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state ST ON, All OFF, IG ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

d.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G69-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
G69-21 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (IG) 8.5 V or higher
Engine switch on (ACC) 8.5 V or higher



Result:
Proceed to
OK
NG



OK

19.INSPECT IG1 NO. 1 RELAY

NG

25.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
19.INSPECT IG1 NO. 1 RELAY
a.

Remove the IG1 NO. 1 relay.


b.
A232574E02
3.198,1.523 3.303,1.666 0.105,0.143 10 3 2.815,1.606 3.17,1.606 false 3.198,1.049 3.303,1.192 0.105,0.143 10 5 2.815,1.132 3.17,1.132 false 1.926,0.319 2.031,0.462 0.105,0.143 10 1 2.325,0.702 2.04,0.403 false 3.198,0.319 3.303,0.462 0.105,0.143 10 2 2.921,0.714 3.176,0.403 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO. 1 RELAY)

NG

REPLACE IG1 NO. 1 RELAY

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO. 1 RELAY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG1 NO. 1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-20 (IG1D) - IG1 NO. 1 relay terminal 1 Always Below 1 Ω
IG1 NO. 1 relay terminal 2 - Body ground Always Below 1 Ω
G69-20 (IG1D) or IG1 NO. 1 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT IG2 RELAY
a.

Remove the IG2 relay.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)

NG

REPLACE IG2 RELAY

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-20 (IG1D) - IG2 relay terminal 1 Always Below 1 Ω
IG2 relay terminal 2 - Body ground Always Below 1 Ω
G69-20 (IG1D) or IG2 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

b.

Remove the body ECU from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B342624C10
1.031,0.333 1.417,0.583 0.385,0.25 2.615,0.333 3,0.583 0.385,0.25 4.167,0.333 4.552,0.583 0.385,0.25 5.75,0.333 6.135,0.583 0.385,0.25 1.031,0.063 1.417,0.292 0.385,0.229 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 1.146,0.094 1.458,0.292 0.313,0.198 10 false 2A 2.729,0.365 3.042,0.563 0.313,0.198 10 false 2P 4.281,0.365 4.594,0.563 0.313,0.198 10 false 2E 5.865,0.365 6.177,0.563 0.313,0.198 10 false 2J 1.135,0.385 1.448,0.583 0.313,0.198 10 false 2R 1.469,0.083 1.771,0.281 0.302,0.198 10 false (*A) 1.469,0.354 1.771,0.563 0.302,0.208 10 false (*B)
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2A-1 - 2P-5 Battery voltage not applied to terminals 2E-2 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2E-2 and 2J-5 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
2R-1 - 2P-5 Battery voltage not applied to terminals 2E-2 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2E-2 and 2J-5 Below 1 Ω



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2E and 2J instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-21 (ACCD) - 2E-2 Always Below 1 Ω
2J-5 - Body ground Always Below 1 Ω
G69-21 (ACCD) or 2E-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

26.INSPECT ENGINE SWITCH
26.INSPECT ENGINE SWITCH


Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G81 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-18 (SSW1) - G81-5 (SS1) Always Below 1 Ω
G69-16 (SSW2) - G81-1 (SS2) Always Below 1 Ω
G69-24 (AGND) - G81-6 (AGND) Always Below 1 Ω
G69-18 (SSW1) or G81-5 (SS1) - Body ground Always 10 kΩ or higher
G69-16 (SSW2) or G81-1 (SS2) - Body ground Always 10 kΩ or higher
G69-24 (AGND) or G81-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A35 stop light switch assembly connector.


c.
C326209C02
1.458,0.208 1.875,0.458 0.417,0.25 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.531,0.25 1.885,0.448 0.354,0.198 10 false A35
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-2 - Body ground Always 11 to 14 V



d.

Connect the A35 stop light switch assembly connector.


e.
B342622C24
1.5,0.25 1.917,0.5 0.417,0.25 0.615,1.302 0.375,1.792 true 0.26,0.229 0.573,0.385 0.313,0.156 10 false *a 1.573,0.292 2.031,0.49 0.458,0.198 10 false G69 0.219,1.802 0.833,2 0.615,0.198 10 false STP1
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-11 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B2 clutch start switch assembly connector.


c.

Disconnect the C53*1, G85*2, C15*3 or G84*4 ECM connector.

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: for 1GR-FE

*4: for 1KD-FTV, 2KD-FTV



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - B2-2 Always Below 1 Ω
G70-16 (STAR) or B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR