84820
1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on Driver Door Window Only)
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Double Cab, RHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (U) - 4 (A)
4 (A) - 9 (E) 6 (D) - 7 (B) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 9 (E)
6 (D) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
6 (D) - 9 (E) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
4 (A) - 6 (D) 6 (D) - 9 (E) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 7 (B) - 10 (U)
9 (E) - 18 (D) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 18 (D)
9 (E) - 10 (U) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| 7 (B) - 15 (U)
9 (E) - 16 (D) |
Manual UP (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 16 (D)
9 (E) - 15 (U) |
Manual DOWN (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 16 (D)
15 (U) - 16 (D) |
OFF (for rear RH door) | Below 1 Ω |
| 7 (B) - 12 (U)
9 (E) - 13 (D) |
Manual UP (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 13 (D)
9 (E) - 12 (U) |
Manual DOWN (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 12 (U) - 13 (D)
9 (E) - 13 (D) |
OFF (for rear LH door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
for Single Cab, Smart Cab, RHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, replace the power window regulator master switch assembly.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (U) - 4 (A)
4 (A) - 9 (E) 6 (D) - 7 (B) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 9 (E)
6 (D) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
6 (D) - 9 (E) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
4 (A) - 6 (D) 6 (D) - 9 (E) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 7 (B) - 10 (U)
9 (E) - 18 (D) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 18 (D)
9 (E) - 10 (U) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Double Cab, LHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1(E) - 4 (A)
3 (U) - 7 (B) 4 (A) - 6 (D) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 6 (D)
3 (U) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
6 (D) - 7 (B) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
3 (U) - 4 (A) 6 (D) - 7 (B) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 1(E) - 18 (D)
7 (B) - 10 (U) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 10 (U)
7 (B) - 18 (D) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| 1(E) - 16 (D)
7 (B) - 15 (U) |
Manual UP (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 15 (U)
7 (B) - 16 (D) |
Manual DOWN (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 16 (D)
15 (U) - 16 (D) |
OFF (for rear RH door) | Below 1 Ω |
| 1(E) - 13 (D)
7 (B) - 12 (U) |
Manual UP (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 12 (U)
7 (B) - 13 (D) |
Manual DOWN (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 13 (D)
12 (U) - 13 (D) |
OFF (for rear LH door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Single Cab, Smart Cab, LHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1(E) - 4 (A)
3 (U) - 7 (B) 4 (A) - 6 (D) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 6 (D)
3 (U) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
6 (D) - 7 (B) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
3 (U) - 4 (A) 6 (D) - 7 (B) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 1(E) - 18 (D)
7 (B) - 10 (U) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 10 (U)
7 (B) - 18 (D) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for RHD:
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 17 (ILL+)
Battery negative (-) → 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for LHD:
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 11 (ILL+)
Battery negative (-) → 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
84820
2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Jam Protection Function)
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Double Cab, RHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (U) - 4 (A)
4 (A) - 9 (E) 6 (D) - 7 (B) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 9 (E)
6 (D) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
6 (D) - 9 (E) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
4 (A) - 6 (D) 6 (D) - 9 (E) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 7 (B) - 10 (U)
9 (E) - 18 (D) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 18 (D)
9 (E) - 10 (U) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| 7 (B) - 15 (U)
9 (E) - 16 (D) |
Manual UP (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 16 (D)
9 (E) - 15 (U) |
Manual DOWN (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 16 (D)
15 (U) - 16 (D) |
OFF (for rear RH door) | Below 1 Ω |
| 7 (B) - 12 (U)
9 (E) - 13 (D) |
Manual UP (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 13 (D)
9 (E) - 12 (U) |
Manual DOWN (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 12 (U) - 13 (D)
9 (E) - 13 (D) |
OFF (for rear LH door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
for Single Cab, RHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, replace the power window regulator master switch assembly.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (U) - 4 (A)
4 (A) - 9 (E) 6 (D) - 7 (B) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 9 (E)
6 (D) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
6 (D) - 9 (E) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 7 (B)
4 (A) - 6 (D) 6 (D) - 9 (E) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (D)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 7 (B) - 10 (U)
9 (E) - 18 (D) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 7 (B) - 18 (D)
9 (E) - 10 (U) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 9 (E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Double Cab, LHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1(E) - 4 (D)
3 (U) - 7 (B) 4 (D) - 6 (U) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 6 (U)
3 (U) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
6 (U) - 7 (B) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
3 (U) - 4 (D) 6 (U) - 7 (B) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (U)
6 (U) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 1(E) - 18 (D)
7 (B) - 10 (U) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 10 (U)
7 (B) - 18 (D) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
| 1(E) - 16 (D)
7 (B) - 15 (U) |
Manual UP (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 15 (U)
7 (B) - 16 (D) |
Manual DOWN (for rear RH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 16 (D)
15 (U) - 16 (D) |
OFF (for rear RH door) | Below 1 Ω |
| 1(E) - 13 (D)
7 (B) - 12 (U) |
Manual UP (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 12 (U)
7 (B) - 13 (D) |
Manual DOWN (for rear LH door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 13 (D)
12 (U) - 13 (D) |
OFF (for rear LH door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for Single Cab, LHD:
Turn the window lock switch off and operate the switches on the power window regulator master switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1(E) - 4 (D)
3 (U) - 7 (B) 4 (D) - 6 (U) |
Auto UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 6 (U)
3 (U) - 7 (B) |
Manual UP (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
6 (U) - 7 (B) |
Manual DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 3 (U)
3 (U) - 4 (D) 6 (U) - 7 (B) |
Auto DOWN (for driver door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 3 (U) - 6 (U)
6 (D) - 7 (B) |
OFF (for driver door) | Below 1 Ω |
| 1(E) - 18 (D)
7 (B) - 10 (U) |
Manual UP (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 10 (U)
7 (B) - 18 (D) |
Manual DOWN (for front passenger door) | Below 1 Ω |
| Not operated | 10 kΩ or higher | |
| 1(E) - 18 (D)
10 (U) - 18 (D) |
OFF (for front passenger door) | Below 1 Ω |
If the result is not as specified, replace the power window regulator master switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for RHD:
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 17 (ILL+)
Battery negative (-) → 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
for LHD:
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 11 (ILL+)
Battery negative (-) → 5 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.
84820
3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Entry and Start System)
| *a | Component without harness connected
(Power Window Regulator Master Switch Assembly) |
Check that the LED illuminates.
Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 3 (ILL+)
Battery negative (-) → 13 (ILL-) |
LED illuminates |
If the result is not as specified, replace the power window regulator master switch assembly.