Home › Vehicle Exterior › WINDOW / GLASS › REAR POWER WINDOW SWITCH(for Double Cab)
RM3250E _59 Vehicle Exterior _038075 WINDOW / GLASS _0185626 REAR POWER WINDOW SWITCH(for Double Cab) G

WINDOW / GLASS  REAR POWER WINDOW SWITCH(for Double Cab)  INSPECTION  


PROCEDURE

Hide 84810D 1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

a.

for Models with Jam Protection Function on Driver Door Window Only:

i.
B405964C01
2.104,0.969 2.583,0.969 true 1.813,0.906 2.542,0.406 true 1.323,0.969 0.698,0.729 true 1.323,1.26 0.688,1.521 true 2.094,1.281 2.552,1.51 true 0.198,0.125 0.51,0.281 0.313,0.156 10 false *a 2.646,0.865 2.802,1.063 0.156,0.198 10 false D 2.604,0.281 2.76,0.479 0.156,0.198 10 false B 0.469,0.625 0.781,0.823 0.313,0.198 10 false SU 2.604,1.448 2.917,1.646 0.313,0.198 10 false SD 0.552,1.427 0.708,1.625 0.156,0.198 10 false U
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check the switch function.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (D) - 4 (SD)
2 (B) - 7 (U)
UP Below 1 Ω
Not operated 10 kΩ or higher
1 (D) - 2 (B)
3 (SU) - 7 (U)
DOWN Below 1 Ω
Not operated 10 kΩ or higher
1 (D) - 4 (SD)
3 (SU) - 7 (U)
OFF Below 1 Ω


If the result is not as specified, replace the rear power window regulator switch assembly.


ii.
B405964C02
1.625,1.333 1.198,1.74 true 1.844,1.333 2.26,1.74 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.885,1.656 1.5,1.854 0.615,0.198 10 false ILL+ 2.323,1.656 2.938,1.854 0.615,0.198 10 false ILL-
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check that the LED illuminates.

Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 5 (ILL-)
LED illuminates


If the result is not as specified, replace the rear power window regulator switch assembly.



b.

except Models with Jam Protection Function on Driver Door Window Only:

i.
B200017C02
1.625,1.01 1.677,1.521 true 1.271,1.021 1.146,1.5 true 1.042,0.99 0.646,1.5 true 1.854,1.021 2.146,1.5 true 2.156,1.01 2.667,1.479 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 2.01,1.542 2.625,1.74 0.615,0.198 10 false DOWN 1.615,1.542 1.927,1.74 0.313,0.198 10 false UP 1.01,1.542 1.469,1.74 0.458,0.198 10 false GND 0.417,1.552 1.031,1.75 0.615,0.198 10 false AUTO 2.688,1.531 3,1.729 0.313,0.198 10 false IG
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check the switch function.

Measure the resistance when the switch is operated according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (IG) - 4 (DOWN)
5 (UP) - 7 (GND)
7 (GND) - 8 (AUTO)
Auto UP Below 1 Ω
Not operated 10 kΩ or higher
2 (IG) - 4 (DOWN)
5 (UP) - 7 (GND)
Manual UP Below 1 Ω
Not operated 10 kΩ or higher
2 (IG) - 5 (UP)
4 (DOWN) - 7 (GND)
Manual DOWN Below 1 Ω
Not operated 10 kΩ or higher
2 (IG) - 5 (UP)
4 (DOWN) - 7 (GND)
7 (GND) - 8 (AUTO)
Auto DOWN Below 1 Ω
Not operated 10 kΩ or higher
2 (IG) - 4 (DOWN)
4 (DOWN) - 5 (UP)
OFF Below 1 Ω


If the result is not as specified, replace the rear power window regulator switch assembly.


ii.
B200017C01
2.01,1.021 1.74,1.448 true 2.365,1.021 2.615,1.458 true 0.094,0.115 0.406,0.271 0.313,0.156 10 false *a 2.583,1.49 3.198,1.688 0.615,0.198 10 false ILL- 1.604,1.469 2.219,1.667 0.615,0.198 10 false ILL+
*a Component without harness connected
(Rear Power Window Regulator Switch Assembly)


Check that the LED illuminates.

Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (ILL+)
Battery negative (-) → 1 (ILL-)
LED illuminates


If the result is not as specified, replace the rear power window regulator switch assembly.