Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0185766 REAR AXLE SHAFT A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT  DISASSEMBLY  


PROCEDURE

Hide 47043C 1.REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

a.
C190684

Temporarily install the 4 nuts to the 4 backing plate to rear axle housing setting bolts.

NOTICE:

Do not use any nuts removed from the vehicle, as they may be damaged.



b.

Using a hammer, tap out the 4 backing plate to rear axle housing setting bolts from the rear brake backing plate sub-assembly LH.


c.

Remove the 4 nuts from the 4 backing plate to rear axle housing setting bolts.


Hide 42423B 2.REMOVE REAR AXLE BEARING INNER RETAINER LH

a.
C190686

Using a snap ring expander, remove the snap ring.


b.
C190689

Grind the retainer surface using a grinder, and then pry off the retainer with a chisel and hammer.

NOTICE:

Be careful not to damage the axle shaft.



c.

Remove the shaft washer from the axle shaft.


Hide 42312 3.REMOVE REAR AXLE SHAFT LH

a.

Insert the setting bolts into the backing plate and temporarily install washers and nuts to the setting bolts. Tighten the nuts to temporarily install the setting bolts to the backing plate and bearing case.


b.

Remove the nuts and washers from the setting bolts.


c.
C190687N03
0.896,0.313 1.292,0.313 1.292,0.313 1.354,0.458 false 0.615,0.25 1.24,0.708 0.625,0.458 10 false SST

Install SST to the backing plate with the 4 nuts.

SST
09521-25012  


d.
C190688N04
2.542,0.552 2.302,0.552 2.302,0.552 2.042,1.323 true 2.615,0.469 3.094,0.896 0.479,0.427 10 false SST

Using SST and a press, press out the rear axle shaft.


e.

Remove the 4 nuts and SST.


f.

Temporarily install 4 nuts to the setting bolts.

NOTICE:

Do not use any nuts removed from the vehicle, as they may be damaged.



g.

Using a hammer, tap out the 4 setting bolts from the backing plate.


h.

Remove the 4 nuts and 4 setting bolts.


Hide 42312E 4.REMOVE REAR AXLE HUB BOLT LH

a.
C190690N02
2.198,0.281 2.063,0.281 2.063,0.281 1.875,0.417 false 2.25,0.208 2.688,0.51 0.438,0.302 10 false SST

Secure the axle shaft between aluminum plates in a vise.


b.

for 2WD:

Using SST, remove the 5 hub bolts.

SST
09650-17011  


c.
C191008N03
2.156,0.313 1.917,0.313 1.917,0.313 1.802,0.5 false 2.229,0.24 2.625,0.563 0.396,0.323 10 false SST

for 4WD and Pre-Runner:

Using SST, remove the 6 hub bolts.

SST
09650-17011  


d.

Remove the deflector and gasket from the axle shaft.

NOTICE:
·

Do not deform the deflector.

·

Make sure to align the groove of SST with the flange of the oil deflector.




Hide 42311E 5.REMOVE REAR AXLE SHAFT OUTER OIL SEAL

a.
C325064N01
2.563,1.792 2.823,1.635 false 2.906,1.531 3.323,1.76 0.417,0.229 10 false SST

Using SST, tap out the rear axle shaft outer oil seal.

SST
09308-00010  


Hide 42312A 6.REMOVE REAR AXLE SHAFT BEARING LH

a.
C325065N01
2.656,1.385 2.865,1.198 false 1.844,3 2.417,2.26 false 2.938,1.115 3.396,1.313 0.458,0.198 10 false SST 1.542,3 2,3.198 0.458,0.198 10 false SST

Using SST and a press, press out the rear axle shaft bearing LH.

SST
09223-56010  
09950-60010  (09951-00650)