Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0185766 REAR AXLE SHAFT A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT  REASSEMBLY  


PROCEDURE

Hide 42312A 1.INSTALL REAR AXLE SHAFT BEARING LH

a.
C325066N01
2.646,1.323 2.854,0.365 false 2.896,0.198 3.354,0.396 0.458,0.198 10 false SST

Using SST and a press, press in a new rear axle shaft bearing LH.

SST
09950-60020  (09951-00810)


Hide 42311E 2.INSTALL REAR AXLE SHAFT OUTER OIL SEAL

a.
C325067N01
0.99,1.26 1.49,1.031 1.49,1.031 1.135,1.729 false 1.573,0.906 2.031,1.104 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)


Hide 42312E 3.INSTALL REAR AXLE HUB BOLT LH

a.
C191260C03
2.906,1.875 2.906,2.104 2.906,2.104 1.292,2.104 true 1.469,1.115 1.469,2.104 true 2.135,1.49 2.135,2.104 true 2.781,4.188 2.781,4.438 2.781,4.438 1.167,4.438 true 1.292,3.427 1.292,4.438 true 1.958,3.688 1.958,4.438 true 0.063,0.052 0.479,0.24 0.417,0.188 10 false *A 1.063,2.01 1.458,2.271 0.396,0.26 10 false *a 0.083,2.26 0.5,2.448 0.417,0.188 10 false *B 0.979,4.344 1.302,4.573 0.323,0.229 10 false *a
*A for 2WD
*B for 4WD and Pre-Runner
*a Oil Drain Hole


Install a new gasket and the deflector to the axle shaft.

HINT:

Align the 3 oil drain holes.



b.

for 2WD:

Pass 5 new hub bolts through the axle hub.


c.

for 4WD and Pre-Runner:

Pass 6 new hub bolts through the axle hub.


d.

Secure the axle shaft between aluminum plates in a vise.


e.
C191019C01
2.896,0.865 2.896,0.365 true 2.646,1.75 3.031,1.198 true 2.781,0.156 3.094,0.313 0.313,0.156 10 false *1 2.458,1.719 2.74,1.938 0.281,0.219 10 false *2
*1 Washer
*2 Nut


for 2WD:

Temporarily install a washer and nut to each of the 5 rear axle hub bolts as shown in the illustration.


f.
C191194C02
2.958,0.896 2.958,0.281 true 2.625,1.823 3.094,1.229 true 2.865,0.052 3.177,0.208 0.313,0.156 10 false *1 2.396,1.771 2.708,1.927 0.313,0.156 10 false *2
*1 Washer
*2 Nut


for 4WD and Pre-Runner:

Temporarily install a washer and nut to each of the 6 rear axle hub bolts as shown in the illustration.


g.

Install the rear axle hub bolts by tightening each nut.


h.

Remove the washer and nut from each rear axle hub bolt.


Hide 47043C 4.INSTALL BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

a.
C190710

Position the backing plate on the bearing case.


b.

Using 2 socket wrenches and a press, press in 4 new backing plate to rear axle housing setting bolts.


Hide 42423B 5.INSTALL REAR AXLE BEARING INNER RETAINER LH

a.
C190695C06
2.063,1.646 1.521,1.646 false 2.104,1.75 1.75,1.75 false 1.75,1.75 1.75,1.646 false 0.396,2.469 0.198,2.469 0.198,2.469 0.198,1.833 false 0.198,1.844 0.448,1.177 true 0.74,2.188 0.563,2.188 0.563,2.188 0.563,1.927 false 0.563,1.938 1.083,0.917 true 2.885,0.375 2.719,0.375 2.719,0.375 2.385,0.854 false 1.229,1.552 1.531,1.698 0.302,0.146 10 false SST 2.938,0.26 3.229,0.417 0.292,0.156 10 false SST 0.823,2.094 1.167,2.333 0.344,0.24 10 false *a 0.479,2.406 0.823,2.646 0.344,0.24 10 false *b
*a Tapered Surface
*b Chamfered Surface


Heat a new retainer to approximately 70 to 130°C (158 to 266°F).


b.

Install a new shaft washer and the retainer to the axle shaft as shown in the illustration.

NOTICE:
·

Install the shaft washer with its tapered surface facing downward.

·

Install the retainer with its chamfered surface facing downward.




c.

Using SST and a press, press in the axle shaft.

SST
09951-01100  
09631-12090  
09726-40010  


d.

Using a snap ring expander, install a new snap ring.