Wear protective gloves. Sharp areas on the parts may injure your hands.
71485C
1.INSTALL REAR SEAT HINGE COVER RH
Perform the following only when replacing the rear seat hinge cover RH.
Do not reuse the rear seat hinge cover RH after removing it.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to attach the guide.
Push in installation direction (2) shown in the illustration to attach the claw to install a new rear seat hinge cover RH.
71486C
2.INSTALL REAR SEAT HINGE COVER LH
Perform the following only when replacing the rear seat hinge cover LH.
Do not reuse the rear seat hinge cover LH after removing it.
Use the same procedure described for the RH side.
78950
3.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
Install the No. 1 fold seat stopper band assembly to the rear No. 2 seat lock assembly.
72630F
4.INSTALL REAR NO. 2 SEAT LOCK ASSEMBLY
Install the rear No. 2 seat lock assembly together with the No. 1 fold seat stopper band assembly with the 2 bolts.
71223
5.INSTALL REAR SEAT CUSHION SIDE BRACKET RH
Install the rear seat cushion side bracket RH with the bolt.
71223
6.INSTALL REAR SEAT CUSHION SIDE BRACKET LH
Use the same procedure described for the RH side.
79101
7.INSTALL NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY
Install the No. 1 seat cushion frame sub-assembly together with the 2 rear seat cushion side brackets with the 2 bushes and 2 bolts.
72995
8.INSTALL REAR SEAT CUSHION COVER RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to attach the guide.
Push in installation direction (2) shown in the illustration to attach the claw to install the rear seat cushion cover RH.
72998B
9.INSTALL REAR SEAT CUSHION COVER LH
Use the same procedure described for the RH side.
10.INSTALL SEAT COVER WIRE
Install the seat cover wire.
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 270 mm (10.63 in.) |
| B | 180 mm (7.09 in.) |
| C | 120 mm (4.72 in.) |
The dimensions shown in the illustration are the lengths.
79011A
11.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
Align the seam allowance in a single direction as shown in the illustration.
Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad with 24 new hog rings in the order indicated in the illustration.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
Be careful not to damage the No. 1 seat cushion cover sub-assembly RH.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly RH.
Install the hog rings at the cutouts if they are there.
12.INSTALL REAR SEAT CUSHION COVER WITH PAD
|
Install in this Direction |
Install the rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly.
Pass the No. 1 fold seat stopper band assembly through the hole of the No. 1 seat cushion cover sub-assembly.
Close the 2 fasteners.
Store the 2 fasteners.
Attach the hook.
13.INSTALL SEAT COVER WIRE
Install the seat cover wire.
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 270 mm (10.63 in.) | B | 300 mm (11.81 in.) |
The dimensions shown in the illustration are the lengths.
79013A
14.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY
When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
Align the seam allowance in a single direction as shown in the illustration.
Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the No. 1 seatback pad with 12 new hog rings in the order indicated in the illustration.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
Be careful not to damage the No. 1 seatback cover sub-assembly.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly.
Install the hog rings at the cutouts if they are there.
15.INSTALL REAR SEATBACK COVER WITH PAD
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to install the rear seatback cover with pad.
Push in the rear end of the rear seatback cover with pad in installation direction (2) shown in the illustration.
Attach the hooks in the order indicated in the illustration.
71931B
16.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
|
Install in this Direction |
w/o Center Headrest:
Attach the claw to install the 4 rear No. 1 seat headrest support assemblies.
|
Install in this Direction |
w/ Center Headrest:
Attach the claw to install the 6 rear No. 1 seat headrest support assemblies.
71960B
17.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Center Headrest)
Install the rear seat center headrest assembly.
71940A
18.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the 2 rear seat headrest assemblies.
Attach the No. 1 fold seat stopper band assembly to the stay of the rear seat headrest assembly and temporarily fix the rear seat cushion assembly in place.