Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY
RM3250E _59 Vehicle Exterior _038067 LIGHTING (EXT) _0185803 REAR COMBINATION LIGHT ASSEMBLY A

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81565 1.INSTALL REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH (w/ Deck)

a.

Attach the connector to install the rear combination light socket and wire sub-assembly LH.


Hide 81562 2.INSTALL REAR COMBINATION LIGHT LENS GASKET LH (for Deck-less)

a.
E323564C01
2.156,2.979 1.823,2.594 true 2.125,3.01 2.438,3.167 0.313,0.156 10 false *a
*a Notch
V100155

Rear Combination Light Lens Gasket LH


Install the rear combination light lens gasket LH to the rear combination light body.

NOTICE:
·

If the rear combination light lens gasket LH has been damaged, replace it with a new one.

·

Position the notch of the rear combination light lens gasket LH at the lower center of the rear combination light body.




Hide 81550Q 3.INSTALL NO. 1 REAR FOG LIGHT BULB (w/ Rear Fog Light)

a.
E296856C02
1,1.104 1.427,1.104 false 1.948,1.104 2.375,1.104 false 0.802,1 1.115,1.156 0.313,0.156 10 false *a 2.438,1 2.75,1.156 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the No. 1 rear fog light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.


b.
E316940C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the No. 1 rear fog light bulb, turn the bulb clockwise to install the bulb.


c.
E316942C01
1.854,1.313 2.271,0.896 true 1.521,3.917 1.781,4.271 true 1.885,1.427 2.375,1.51 true 2.333,0.75 2.542,0.938 0.208,0.188 10 true *a 1.833,4.198 2.042,4.385 0.208,0.188 10 true *c 2.427,1.417 2.646,1.615 0.219,0.198 10 true *b
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Clockwise


Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.


Hide 81550N 4.INSTALL BACK UP LIGHT BULB

a.
E296856C02
1,1.104 1.427,1.104 false 1.948,1.104 2.375,1.104 false 0.802,1 1.115,1.156 0.313,0.156 10 false *a 2.438,1 2.75,1.156 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


w/ Deck:

i.

Align the 2 protrusions on the back up light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.


ii.
E316940C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the back up light bulb, turn the bulb clockwise to install the bulb.


iii.
E316938C01
1.115,0.938 1.573,0.719 true 1.083,0.594 1.542,0.594 true 1.927,3.333 2.385,3.115 true 0.948,0.865 1.125,1.042 0.177,0.177 10 true *a 0.896,0.51 1.083,0.688 0.188,0.177 10 true *b 2.385,3.01 2.573,3.177 0.188,0.167 10 true *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Clockwise


Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.



b.

for Deck-less:

i.
E296841C02
0.969,1.146 1.438,1.146 false 1.979,1.146 2.448,1.146 false 0.76,1.042 1.073,1.198 0.313,0.156 10 false *a 2.5,1.052 2.813,1.208 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the back up light bulb with the 2 cutouts of the rear combination light body and insert the bulb to the rear combination light body.


ii.
E323558C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the back up light bulb, turn the bulb clockwise to install the bulb.



Hide 81550L 5.INSTALL REAR TURN SIGNAL LIGHT BULB

a.
E296856C02
1,1.104 1.427,1.104 false 1.948,1.104 2.375,1.104 false 0.802,1 1.115,1.156 0.313,0.156 10 false *a 2.438,1 2.75,1.156 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


w/ Deck:

i.

Align the 2 protrusions on the rear turn signal light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.


ii.
E316936C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.


iii.
E316934C01
1.115,0.948 1.594,0.74 true 1.125,0.594 1.563,0.594 true 1.49,3.188 1.906,3.333 true 0.948,0.875 1.135,1.052 0.188,0.177 10 true *a 0.938,0.5 1.125,0.677 0.188,0.177 10 true *b 1.313,3.083 1.49,3.26 0.177,0.177 10 true *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Clockwise


Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.



b.

for Deck-less:

i.
E296841C02
0.969,1.146 1.438,1.146 false 1.979,1.146 2.448,1.146 false 0.76,1.042 1.073,1.198 0.313,0.156 10 false *a 2.5,1.052 2.813,1.208 0.313,0.156 10 false *a
*a Protrusion
V100135

Cutout


Align the 2 protrusions on the rear turn signal light bulb with the 2 cutouts of the rear combination light body and insert the bulb to the rear combination light body.


ii.
E323554C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.



Hide 81550H 6.INSTALL TAIL AND STOP LIGHT BULB

a.
E296855C02
0.927,1.135 1.427,1.135 false 2.135,1 2.635,1 false 2.698,0.906 3.01,1.063 0.313,0.156 10 false *a 0.74,1.042 1.052,1.198 0.313,0.156 10 false *b
*a Upper Protrusion
*b Lower Protrusion
V100136

Long Cutout
V100137

Short Cutout


w/ Deck:

i.

Align the upper protrusion of the tail and stop light bulb with the short cutout of the bulb socket and the lower protrusion with the long cutout, and then insert the bulb.


ii.
E316932C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the tail and stop light bulb, turn the bulb clockwise to install the bulb.


iii.
E316930C01
1.177,0.865 1.594,0.708 true 1.188,0.5 1.583,0.583 true 1.938,3.333 2.354,3.177 true 0.99,0.781 1.198,0.979 0.208,0.198 10 true *a 1.01,0.396 1.198,0.573 0.188,0.177 10 true *b 2.375,3.073 2.594,3.26 0.219,0.188 10 true *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark
V113147

Clockwise


Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.



b.

for Deck-less:

i.
E296842C02
0.813,1.219 1.365,1.219 false 2.063,1.083 2.615,1.083 false 2.667,0.969 2.979,1.125 0.313,0.156 10 false *a 0.625,1.115 0.938,1.271 0.313,0.156 10 false *b
*a Upper Protrusion
*b Lower Protrusion
V100136

Long Cutout
V100137

Short Cutout


Align the upper protrusion of the tail and stop light bulb with the short cutout of the rear combination light body and the lower protrusion with the long cutout, and then insert the bulb to the rear combination light body.


ii.
E323556C01
0,0 0,0 false
V113147

Push in this Direction
V113148

Clockwise


While pushing the tail and stop light bulb, turn the bulb clockwise to install the bulb.



Hide 81561 7.INSTALL REAR COMBINATION LIGHT LENS LH (for Deck-less)

a.

Install the rear combination light lens LH to the rear combination light body.