Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/ VSC) › 2015.06–2016.03
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0186155 BRAKE ACTUATOR(w/ VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ VSC)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Skid control ECU (Brake actuator assembly) Yaw rate and acceleration sensor zero point calibration and store system information
·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 4.REMOVE BRAKE ACTUATOR WITH BRACKET

a.

Place tags or marks to identify the installation locations of each brake line.

C332384C01
4.479,0.865 5.115,0.865 true 4.656,1.208 5.083,1.208 5.083,1.208 5.323,1.01 true 5.25,1.406 5.427,1.406 5.427,1.406 5.542,1.125 true 5.792,1.271 6.208,1.271 true 4.792,2.063 4.792,1.469 true 5.323,1.885 5.885,1.885 true 0.875,1.375 1.396,1.375 true 0.802,0.948 1.25,0.948 1.25,0.948 1.573,1.198 true 1.76,1.073 2.438,1.073 true 1.927,0.844 2.219,0.844 true 1.844,2.323 1.844,1.854 true 2.635,2.031 2.292,2.031 2.292,2.031 2.292,1.385 true 4.302,0.771 4.5,0.969 0.198,0.198 10 true *a 4.458,1.104 4.646,1.302 0.188,0.198 10 true *b 5.073,1.302 5.229,1.5 0.156,0.198 10 true *c 6.25,1.167 6.469,1.375 0.219,0.208 10 true *c 4.708,2.125 4.917,2.323 0.208,0.198 10 true *d 5.927,1.781 6.156,1.99 0.229,0.208 10 true *d 0.135,0.042 0.51,0.281 0.375,0.24 12 false *A 3.813,0.052 4.125,0.25 0.313,0.198 12 false *B 0.677,1.271 0.865,1.469 0.188,0.198 10 true *a 0.604,0.844 0.802,1.042 0.198,0.198 10 true *b 2.479,0.979 2.667,1.177 0.188,0.198 10 true *c 2.26,0.75 2.438,0.948 0.177,0.198 10 true *c 1.781,2.354 2,2.542 0.219,0.188 10 true *d 2.677,1.917 2.885,2.115 0.208,0.198 10 true *d
*A for LHD *B for RHD
*a To Front Wheel Cylinder RH *b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder *d From Master Cylinder



b.

Release the lock lever and disconnect the connector from the brake actuator assembly.

C332385C01
0.083,0.031 0.458,0.271 0.375,0.24 12 false *A 3.885,0.031 4.26,0.271 0.375,0.24 12 false *B
*A for LHD *B for RHD
V113147

Lock Lever Released
V113148

Connector Disconnected


NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Detach the clamp from the brake actuator bracket assembly.


d.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

C332386C01
0.156,0.031 0.531,0.271 0.375,0.24 12 false *A 3.823,0.042 4.198,0.281 0.375,0.24 12 false *B
*A for LHD *B for RHD



e.

Remove the 3 nuts and brake actuator with bracket.

C332387C01
0.156,0.021 0.531,0.26 0.375,0.24 12 false *A 3.792,0.031 4.167,0.271 0.375,0.24 12 false *B
*A for LHD *B for RHD


NOTICE:

Do not damage the brake lines.