Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/o VSC)
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0186156 BRAKE ACTUATOR(w/o VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/o VSC)  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.

Install the brake actuator with bracket with the 3 nuts.

C332589C02
0.198,0.031 0.573,0.271 0.375,0.24 12 false *A 3.802,0.021 4.177,0.26 0.375,0.24 12 false *B 4.188,1.563 4.323,1.74 0.135,0.177 10 true C 4.698,2.594 4.823,2.76 0.125,0.167 10 true A 6.229,1.917 6.354,2.094 0.125,0.177 10 true B 2.292,2.333 2.448,2.531 0.156,0.198 10 true A 0.896,2.604 1.042,2.771 0.146,0.167 10 true B 0.625,1.271 0.76,1.438 0.135,0.167 10 true C
*A for LHD *B for RHD


Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 3 nuts uniformly in alphabetical order.

·

Be careful not to damage the brake tubes.




b.

Set each brake line in the correct position on the brake actuator as shown in the illustration.

C332536C01
5.646,0.635 6.125,0.635 true 5.292,0.406 5.49,0.177 5.49,0.177 5.75,0.177 true 5.031,0.323 4.844,0.167 4.844,0.167 4.354,0.167 true 4.49,0.177 4.76,0.448 true 4.635,1.729 4.906,1.729 4.906,1.729 5.167,1.458 true 5.99,1.188 6.406,1.188 true 1.979,1.344 2.406,1.344 true 1.052,1.125 1.708,2.094 1.708,2.094 2.188,2.094 true 2.198,0.708 2.552,0.708 true 1.906,0.583 2.177,0.302 2.177,0.302 2.469,0.302 true 1.594,0.448 1.792,0.104 1.792,0.104 2,0.104 true 0.854,0.208 1.219,0.208 true 0.177,0.021 0.552,0.26 0.375,0.24 12 false *A 3.833,0.021 4.208,0.26 0.375,0.24 12 false *B 6.167,0.521 6.385,0.719 0.219,0.198 10 true *a 5.802,0.083 6.021,0.281 0.219,0.198 10 true *b 4.156,0.063 4.333,0.26 0.177,0.198 10 true *c 4.427,1.635 4.625,1.823 0.198,0.188 10 true *d 6.427,1.094 6.646,1.292 0.219,0.198 10 true *d 2.458,1.26 2.677,1.458 0.219,0.198 10 true *d 2.229,2 2.438,2.198 0.208,0.198 10 true *d 2.594,0.625 2.833,0.823 0.24,0.198 10 true *a 2.531,0.219 2.75,0.406 0.219,0.188 10 true *b 2.042,0.021 2.229,0.219 0.188,0.198 10 true *c 0.635,0.104 0.844,0.302 0.208,0.198 10 true *c
*A for LHD *B for RHD
*a To Front Wheel Cylinder RH *b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder *d From Master Cylinder



c.

Using a union nut wrench, connect the 6 brake lines to the correct locations on the actuator as shown in the illustration.

C332603C01
0.177,0.031 0.469,0.271 0.292,0.24 12 false *A 3.865,0.031 4.135,0.271 0.271,0.24 12 false *B 5.99,0.563 6.219,0.76 0.229,0.198 10 true *a 2.656,0.667 2.865,0.865 0.208,0.198 10 true *a
*A for LHD *B for RHD
*a Torque Wrench Fulcrum Length - -


Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




d.

Attach the clamp to the brake actuator bracket.

C332604C01
0.146,0.031 0.521,0.271 0.375,0.24 12 false *A 3.906,0.021 4.281,0.26 0.375,0.24 12 false *B
*A for LHD *B for RHD
V113147

Connector Connected
V113148

Lock Lever Locked



e.

Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4. SENSOR CHECK USING TEST MODE (SIGNAL CHECK)

NOTICE:

After replacing the skid control ECU (brake actuator assembly), it is necessary to perform registration of rear differential lock identification information. Rear differential lock identification information is automatically acquired when the system enters test mode.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE