Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for Double Cab)
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186370 REAR DOOR(for Double Cab) N

DOOR / HATCH  REAR DOOR(for Double Cab)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·
B276679C19
0.621,1.754 0.818,1.944 0.197,0.19 10 *1 2.535,1.754 2.732,1.944 0.197,0.19 10 *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67004 1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY LH

a.

Check that the clearance measurements of areas A to M are within the standard ranges.

B404337N01
1.271,2.208 1.427,2.406 0.156,0.198 10 false A 1.5,2.427 1.656,2.625 0.156,0.198 10 false B 0.948,0.979 1.104,1.177 0.156,0.198 10 false C 1.448,1.198 1.604,1.396 0.156,0.198 10 false D 2.083,0.177 2.25,0.385 0.167,0.208 10 false E 2.313,0.74 2.479,0.948 0.167,0.208 10 false F 5.01,0.188 5.177,0.396 0.167,0.208 10 false G 5.271,0.719 5.438,0.927 0.167,0.208 10 false H 5.375,1.219 5.542,1.427 0.167,0.208 10 false I 5.875,1.458 6.042,1.667 0.167,0.208 10 false J 5.563,2.385 5.719,2.583 0.156,0.198 10 false K 5.875,2.552 6.031,2.75 0.156,0.198 10 false L 2.583,3.115 2.74,3.313 0.156,0.198 10 false M

Standard Clearance:
Area Measurement Area Measurement
A 3.2 to 6.2 mm (0.126 to 0.244 in.) B -1.5 to 1.5 mm (-0.059 to 0.059 in.)
C 3.2 to 6.2 mm (0.126 to 0.244 in.) D -1.5 to 1.5 mm (-0.059 to 0.059 in.)
E 3.2 to 6.2 mm (0.126 to 0.244 in.) F 1.8 to 4.8 mm (0.071 to 0.189 in.)
G 3.2 to 6.2 mm (0.126 to 0.244 in.) H 0.4 to 3.4 mm (0.016 to 0.134 in.)
I 2.8 to 5.8 mm (0.110 to 0.228 in.) J -1.5 to 1.5 mm (-0.059 to 0.059 in.)
K 2.8 to 5.8 mm (0.110 to 0.228 in.) L -1.5 to 1.5 mm (-0.059 to 0.059 in.)
M 4.2 to 7.2 mm (0.165 to 0.283 in.) - -



Hide 67004 2.ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH

a.
B404339

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B404338

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B404340

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)