Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL SWITCH
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0186381 DOOR CONTROL SWITCH G

DOOR LOCK  DOOR CONTROL SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double Cab, LHD)

a.
B408918C01
2.177,3.625 2.427,2.979 2.427,2.979 2.667,2.979 true 1.688,4.479 1.958,4.479 1.958,4.479 2.188,3.938 true 2.438,0.75 2.438,0.229 2.438,0.229 0.406,0.229 true 2.208,0.531 2.208,0.229 true 1.646,0.99 1.646,0.229 true 1.417,0.781 1.417,0.229 true 0.875,1.292 0.875,0.229 true 0.719,0.99 0.719,0.229 true 0.521,1.063 0.521,0.229 true 0.396,2.781 0.938,3.083 0.542,0.302 10 false *a 1.406,4.385 2.021,4.583 0.615,0.198 10 false ILL- 2.74,2.896 3.354,3.094 0.615,0.198 10 false ILL+ 0.177,0.146 0.49,0.344 0.313,0.198 10 false *b
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/ Entry and Start System)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B412145C03
0.521,1.073 0.521,0.271 0.521,0.271 1.792,0.271 true 0.729,1.01 0.729,0.271 true 0.875,1.302 0.875,0.271 true 1.646,1.042 1.646,0.271 true 1.792,3.51 2.083,2.844 2.083,2.844 2.344,2.844 true 1.865,4.25 1.615,4.25 1.615,4.25 1.333,3.802 true 1.875,0.188 2.188,0.385 0.313,0.198 10 false *b 1.938,4.188 2.552,4.385 0.615,0.198 10 false ILL+ 2.417,2.771 3.031,2.969 0.615,0.198 10 false ILL- 0.792,2.74 1.104,2.938 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B412145C02
0.521,1.073 0.521,0.271 0.521,0.271 1.792,0.271 true 0.729,1.01 0.729,0.271 true 0.875,1.302 0.875,0.271 true 1.646,1.042 1.646,0.271 true 1.792,3.51 2.083,2.844 2.083,2.844 2.344,2.844 true 1.865,4.25 1.615,4.25 1.615,4.25 1.333,3.802 true 1.875,0.188 2.188,0.385 0.313,0.198 10 false *b 1.938,4.188 2.552,4.385 0.615,0.198 10 false ILL+ 2.417,2.771 3.031,2.969 0.615,0.198 10 false ILL- 0.792,2.74 1.104,2.938 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/o Jam Protection Function)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B412144C04
0.844,3.552 1.146,3.552 true 1.344,3.51 1.344,2.844 1.344,2.844 1.51,2.844 true 2.24,3.521 2.24,2.854 2.24,2.854 2.406,2.854 true 0.521,1.083 0.521,0.438 0.521,0.438 0.323,0.438 true 0.729,1.021 0.729,0.375 0.729,0.375 0.885,0.375 true 2.49,2.781 2.802,2.979 0.313,0.198 10 false UL 1.573,2.771 1.729,2.969 0.156,0.198 10 false L 0.708,3.469 0.865,3.667 0.156,0.198 10 false E 0.552,2.615 0.865,2.813 0.313,0.198 10 false *c 0.156,0.344 0.469,0.542 0.313,0.198 10 false *a 0.927,0.281 1.24,0.479 0.313,0.198 10 false *b
*a Lock
*b Unlock
*c Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below. (w/o Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) Lock switch not pushed 10 kΩ or higher
8 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 1 (E) Unlock switch not pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch assembly.


Hide 84820 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double Cab, RHD)

a.
B361186C09
2.177,3.615 2.469,3.021 true 2.406,4.375 2.177,3.927 true 2.333,0.583 2.333,0.25 2.333,0.25 0.417,0.25 true 2.135,0.417 2.135,0.25 true 1.5,0.833 1.5,0.25 true 1.333,0.688 1.333,0.25 true 0.865,1.052 0.875,0.25 true 0.542,0.917 0.542,0.365 0.542,0.365 0.542,0.25 true 0.667,1.146 0.667,0.25 true 2.542,2.906 2.844,3.104 0.302,0.198 10 false ILL+ 2.375,4.396 2.771,4.583 0.396,0.188 10 false ILL- 0.198,0.156 0.813,0.354 0.615,0.198 10 false *b 0.417,2.906 0.667,3.073 0.25,0.167 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/ Entry and Start System)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B408987C01
1.333,0.844 1.333,0.271 true 0.542,1.073 0.542,0.271 true 0.677,1.313 0.677,0.271 true 0.875,1.219 0.875,0.271 true 0.542,0.271 1.771,0.271 false 2.677,4.24 2.479,4.24 2.479,4.24 2.229,3.802 true 1.781,3.51 2.031,2.74 2.031,2.74 2.344,2.74 true 1.833,0.188 2.146,0.385 0.313,0.198 10 false *b 2.385,2.677 2.854,2.896 0.469,0.219 10 false ILL- 2.729,4.167 3.198,4.385 0.469,0.219 10 false ILL+ 0.792,2.698 1.104,2.896 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B408987C05
1.333,0.844 1.333,0.271 true 0.542,1.073 0.542,0.271 true 0.677,1.313 0.677,0.271 true 0.875,1.219 0.875,0.271 true 0.542,0.271 1.771,0.271 false 2.677,4.24 2.479,4.24 2.479,4.24 2.229,3.802 true 1.781,3.51 2.031,2.74 2.031,2.74 2.344,2.74 true 1.833,0.188 2.146,0.385 0.313,0.198 10 false *b 2.385,2.677 2.854,2.896 0.469,0.219 10 false ILL- 2.729,4.167 3.198,4.385 0.469,0.219 10 false ILL+ 0.792,2.698 1.104,2.896 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/o Jam Protection Function)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B408989C01
0.667,1.302 0.667,0.448 0.667,0.448 0.5,0.448 true 0.865,1.229 0.865,0.375 0.865,0.375 1.063,0.375 true 1.333,3.521 1.333,2.583 1.333,2.583 1.594,2.583 true 2.229,3.521 2.229,2.583 2.229,2.583 2.49,2.583 true 2.438,3.563 2.771,3.563 true 0.302,0.354 0.615,0.552 0.313,0.198 10 false *a 1.115,0.302 1.427,0.5 0.313,0.198 10 false *b 1.646,2.51 1.917,2.708 0.271,0.198 10 false UL 2.542,2.51 2.813,2.708 0.271,0.198 10 false L 2.823,3.49 3.094,3.688 0.271,0.198 10 false E 0.833,2.646 1.146,2.844 0.313,0.198 10 false *c
*a Lock
*b Unlock
*c Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below. (w/o Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition
8 (L) - 9 (E) Lock switch pushed Below 1 Ω
8 (L) - 9 (E) Lock switch not pushed 10 kΩ or higher
2 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
2 (UL) - 9 (E) Unlock switch not pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch assembly.


Hide 84820 3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Single Cab, Smart Cab, LHD)

a.
B414985C01
0.531,1.115 0.531,0.271 0.531,0.271 2.031,0.271 true 0.729,1.042 0.729,0.271 true 0.896,1.313 0.896,0.271 true 1.427,0.833 1.427,0.271 true 1.656,1.073 1.656,0.271 true 2.167,3.656 2.167,2.854 2.167,2.854 2.604,2.854 true 1.875,4.365 2.188,4.365 2.188,4.365 2.188,3.927 true 2.667,2.771 3.281,2.969 0.615,0.198 10 false ILL+ 1.594,4.292 2.208,4.49 0.615,0.198 10 false ILL- 0.635,2.656 0.948,2.854 0.313,0.198 10 false *a 2.073,0.188 2.385,0.385 0.313,0.198 10 false *b
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/ Entry and Start System)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B414981C01
0.531,1.063 0.531,0.302 0.531,0.302 1.896,0.302 true 0.719,1 0.719,0.302 true 0.885,1.271 0.885,0.302 true 1.625,1.021 1.625,0.302 true 0.958,4.229 1.344,4.229 1.344,4.229 1.344,3.802 true 1.792,3.5 1.792,2.927 1.792,2.927 2.031,2.927 true 1.948,0.219 2.26,0.417 0.313,0.198 10 false *b 0.76,2.688 1.073,2.885 0.313,0.198 10 false *a 0.656,4.146 1.271,4.344 0.615,0.198 10 false ILL+ 2.125,2.854 2.74,3.052 0.615,0.198 10 false ILL-
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B414981C03
0.531,1.063 0.531,0.302 0.531,0.302 1.896,0.302 true 0.719,1 0.719,0.302 true 0.885,1.271 0.885,0.302 true 1.625,1.021 1.625,0.302 true 0.958,4.229 1.344,4.229 1.344,4.229 1.344,3.802 true 1.792,3.5 1.792,2.927 1.792,2.927 2.031,2.927 true 1.948,0.219 2.26,0.417 0.313,0.198 10 false *b 0.76,2.688 1.073,2.885 0.313,0.198 10 false *a 0.656,4.146 1.271,4.344 0.615,0.198 10 false ILL+ 2.125,2.854 2.74,3.052 0.615,0.198 10 false ILL-
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/o Jam Protection Function)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 11 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B414982C02
0.5,1.073 0.5,0.146 0.5,0.146 1.094,0.146 true 0.719,0.99 0.719,0.438 0.719,0.438 0.927,0.438 true 1.333,3.5 1.333,2.76 1.333,2.76 1.531,2.76 true 2.24,3.51 2.24,2.771 2.24,2.771 2.438,2.771 true 0.792,3.552 1.135,3.552 true 1.167,0.063 1.573,0.292 0.406,0.229 10 false *a 0.99,0.354 1.302,0.552 0.313,0.198 10 false *b 0.49,2.719 0.802,2.917 0.313,0.198 10 false *c 0.656,3.458 0.813,3.656 0.156,0.198 10 false E 1.583,2.677 1.74,2.875 0.156,0.198 10 false L 2.5,2.698 2.771,2.927 0.271,0.229 10 false UL
*a Lock
*b Unlock
*c Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below. (w/o Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) Lock switch not pushed 10 kΩ or higher
8 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 1 (E) Unlock switch not pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch assembly.


Hide 84820 4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Single Cab, Smart Cab , RHD)

a.
B408988C02
0.833,1.042 0.833,0.24 0.833,0.24 1.698,0.24 true 1.146,1.208 1.146,0.24 true 0.969,1.281 0.969,0.24 true 1.458,0.854 1.458,0.24 true 1.625,0.99 1.625,0.24 true 2.094,3.531 2.51,2.781 true 2.5,4.302 2.115,3.854 true 1.75,0.167 2.063,0.365 0.313,0.198 10 false *b 2.573,2.708 3.188,2.906 0.615,0.198 10 false ILL+ 2.583,4.229 3.198,4.427 0.615,0.198 10 false ILL- 0.5,2.563 0.813,2.76 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/ Entry and Start System)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 3 (ILL+)
Battery negative (-) - 13 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B406724C02
0.844,1.052 0.844,0.25 0.844,0.25 1.604,0.25 true 0.99,1.292 0.99,0.25 true 1.146,1.24 1.146,0.25 true 1.458,0.844 1.458,0.25 true 1.615,3.385 1.813,2.594 1.813,2.594 2.115,2.594 true 2.604,4.146 2.375,4.146 2.375,4.146 2.063,3.688 true 1.667,0.167 1.979,0.365 0.313,0.198 10 false *b 2.167,2.521 2.781,2.719 0.615,0.198 10 false ILL- 2.656,4.063 3.271,4.26 0.615,0.198 10 false ILL+ 0.635,2.5 0.948,2.698 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (for Models with Jam Protection Function on Driver Door Window Only)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



c.
B406724C02
0.844,1.052 0.844,0.25 0.844,0.25 1.604,0.25 true 0.99,1.292 0.99,0.25 true 1.146,1.24 1.146,0.25 true 1.458,0.844 1.458,0.25 true 1.615,3.385 1.813,2.594 1.813,2.594 2.115,2.594 true 2.604,4.146 2.375,4.146 2.375,4.146 2.063,3.688 true 1.667,0.167 1.979,0.365 0.313,0.198 10 false *b 2.167,2.521 2.781,2.719 0.615,0.198 10 false ILL- 2.656,4.063 3.271,4.26 0.615,0.198 10 false ILL+ 0.635,2.5 0.948,2.698 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)
*b LED Illumination


Check that the LED illuminates. (w/o Jam Protection Function)

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Battery connection Result
Battery positive (+) - 17 (ILL+)
Battery negative (-) - 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



d.
B408990C01
0.99,1.292 0.99,0.458 0.99,0.458 0.75,0.458 true 1.146,1.229 1.146,0.313 1.146,0.313 1.365,0.313 true 1.167,3.396 1.167,2.479 1.167,2.479 1.365,2.479 true 2.063,3.406 2.063,2.49 2.063,2.49 2.26,2.49 true 2.26,3.448 2.615,3.448 true 0.552,0.365 0.865,0.563 0.313,0.198 10 false *a 1.417,0.229 1.729,0.427 0.313,0.198 10 false *b 1.417,2.417 1.729,2.615 0.313,0.198 10 false UL 2.323,2.417 2.479,2.615 0.156,0.198 10 false L 2.677,3.396 2.833,3.594 0.156,0.198 10 false E 0.729,2.594 1.042,2.792 0.313,0.198 10 false *c
*a Lock
*b Unlock
*c Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below. (w/o Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition
8 (L) - 9 (E) Lock switch pushed Below 1 Ω
8 (L) - 9 (E) Lock switch not pushed 10 kΩ or higher
2 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
2 (UL) - 9 (E) Unlock switch not pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch assembly.