Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE › 2015.06–2016.01
RM3250E _59 Vehicle Exterior _038076 WIPER / WASHER _0186522 WASHER NOZZLE G

WIPER / WASHER  WASHER NOZZLE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85035 1.INSPECT WASHER NOZZLE SUB-ASSEMBLY (for LHD)

a.

for Europe:

i.

With the engine switch turned to on (IG), check the position that the washer fluid hits the windshield.

OK:

Washer fluid hits the windshield in the areas shown in the illustration.


B407783C01
2.094,2.802 0.771,2.802 true 1.781,1.885 0.813,1.885 true 1.552,1.115 0.906,1.115 true 0.719,1.031 1.031,1.188 0.313,0.156 10 false *a 0.635,1.802 0.948,1.958 0.313,0.156 10 false *b 0.563,2.719 0.875,2.875 0.313,0.156 10 false *c 3.24,0.375 3.396,0.573 0.156,0.198 10 true A 3.875,0.375 4.031,0.573 0.156,0.198 10 true A 3.156,4.323 3.313,4.521 0.156,0.198 10 true B 3.948,4.323 4.104,4.521 0.156,0.198 10 true B 4.958,3.115 5.115,3.313 0.156,0.198 10 true C 5.615,2.896 5.771,3.094 0.156,0.198 10 true D
*a Upper Limit *b Standard
*c Lower Limit - -


Standard:
Area Measurement Area Measurement
A 165 mm (6.4960 in.) B 208 mm (8.1890 in.)
C 133 mm (5.2362 in.) D 245 mm (9.6457 in.)


NOTICE:

If the result is not as specified, replace the washer nozzle sub-assembly.




b.

except Europe:

i.

With the engine switch turned to on (IG), check the position that the washer fluid hits the windshield.

OK:

Washer fluid hits the windshield in the areas shown in the illustration.


B407785C01
1.615,1.427 0.896,1.427 true 1.896,2.458 0.833,2.302 true 2.031,2.906 0.74,2.948 true 3.156,0.385 3.313,0.583 0.156,0.198 10 false A 3.854,0.375 4.01,0.573 0.156,0.198 10 false A 3.083,4.292 3.24,4.49 0.156,0.198 10 false B 3.927,4.302 4.083,4.5 0.156,0.198 10 false B 4.833,3.156 4.99,3.354 0.156,0.198 10 false C 5.552,2.948 5.771,3.188 0.219,0.24 10 true D 0.708,1.333 1.021,1.531 0.313,0.198 10 false *a 0.635,2.208 0.948,2.406 0.313,0.198 10 false *b 0.542,2.854 0.854,3.052 0.313,0.198 10 false *c
*a Upper Limit *b Standard
*c Lower Limit - -


Standard:
Area Measurement Area Measurement
A 184 mm (7.2441 in.) B 215 mm (8.4646 in.)
C 115 mm (4.5276 in.) D 197 mm (7.7559 in.)


NOTICE:

If the result is not as specified, replace the washer nozzle sub-assembly.




Hide 85035 2.INSPECT WASHER NOZZLE SUB-ASSEMBLY (for RHD)

a.

With the engine switch turned to on (IG), check the position that the washer fluid hits the windshield.

OK:

Washer fluid hits the windshield in the areas shown in the illustration.


B400417C01
2.052,2.896 0.781,3.083 true 1.896,2.5 0.719,2.5 true 1.646,1.625 0.75,1.625 true 0.552,1.531 0.865,1.688 0.313,0.156 10 false *a 0.531,2.417 0.844,2.573 0.313,0.156 10 false *b 0.573,2.99 0.885,3.146 0.313,0.156 10 false *c 3.167,0.438 3.323,0.635 0.156,0.198 10 false A 3.854,0.438 4.01,0.635 0.156,0.198 10 false A 3.083,4.24 3.24,4.438 0.156,0.198 10 false B 3.906,4.25 4.063,4.448 0.156,0.198 10 false B 4.896,3.177 5.052,3.375 0.156,0.198 10 false C 5.583,2.969 5.74,3.167 0.156,0.198 10 false D
*a Upper Limit *b Standard
*c Lower Limit - -


Standard:
Area Measurement Area Measurement
A 184 mm (7.2441 in.) B 215 mm (8.4646 in.)
C 115 mm (4.5276 in.) D 197 mm (7.7559 in.)


NOTICE:

If the result is not as specified, replace the washer nozzle sub-assembly.